Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Blower only works on high...

Join Wrangler Forum Today


Thread: Blower only works on high... Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-13-2013 03:07 PM
mmbrock77 Ebay has the part, too. I replaced mine in my '05 TJ. It's behind the glove box. Kind of a pain to get to but it's do-able.
05-13-2013 02:51 PM
BigDaddyAt Nice. Now I know what has been the issue...and how to fix it
05-13-2013 08:48 AM
ronpete13 Changed mine this weekend - Works again!! - Don't hurt to have someone with smaller hands
05-06-2013 01:47 PM
thgr8alex Ya autozone wanted 45 bucks for that piece. Found it on quadratec for 27
05-06-2013 01:44 PM
Relocatedduckman It's the resistor under the glove box. Mine was that way. Replaced it.. Boom.. Good air again..
05-06-2013 01:29 PM
thgr8alex My jeep is doimg the same. Only works on the 4th setting. So i got all or nothing..literally. Hah so i was near autozone today and they said it was 45 bucks. Is that too much for one as i saw on here its a 20 dollar fix or so?
05-06-2013 09:45 AM
Neil F.
Quote:
Originally Posted by ronpete13 View Post
Mine works on the 2 higher settings but not on the 2 lower? - 2004 TJ
Thoughts on that....

Replace the blower resistor as indicated. On mine and my neighbors, we lost fan speeds one by one over time.
05-06-2013 09:28 AM
ronpete13 Mine works on the 2 higher settings but not on the 2 lower? - 2004 TJ
Thoughts on that....
05-05-2013 06:56 PM
nvmytj
Mine went out on a 97 TJ

My fan would only work on high and the switch from floor to defrost had stopped working also. Removing the leaves that had filled up in there fixed the switching from floor to defrost and the resistor fixed the speed control.

What in the world did we do before the internet?

03-12-2011 06:58 PM
snow.thrills I had the same problem in the fall. Only high speed would work, sometimes. I replaced the resister and that didn't work. I almost went the blower route but decided to replace the heater control assembly instead after reading some good posts on this AWESOME Forum. Glad I did it was a 30 min at most $90 fix. It turned out the vacuum switch was shot and the back side of the assembly was a little melted which I think caused the vacuum switch to sit in a bad position and fail. According to some of the jeep parts websites you can replace each one of the heater switches/selectors individually, just another decision you may want to consider. It only takes a few minutes to take apart the dash an take out the assembly. I was able to tell my issue as soon as unscrewed it from the dash. A little wiggle on that switch and everything worked as it was supposed to. You may even be able to wiggle that switch from the glove box. Good Luck!
03-12-2011 04:55 PM
99jeeper
switch

Quote:
Originally Posted by Hondarider View Post
2003 TJ 4.0 5spd. So the heater fan only works on the highest setting...nothing happening on the other three settings. Blower motor or the switch? Has anyone seen this before? If this is a common failure, it might save me some time on the troubleshooting side of things. Thanks.
just went thru this same thing last week it was the switch in the dash. i found out the hard way after i bought a new resister and that wasnt it!
03-12-2011 04:46 PM
DCP10 Was able to replace fan motor resistor for '99 TJ with a wrench and a new $47 NAPA brand fan motor resistor in about 10 minutes.

Differential diagnosis for faulty AC/heat fan speeds: (1) faulty fan motor resistor, (2) shot fan motor, (3) HVAC manual dashboard control defect, (4) faulty fuses, and/or (5) underlying electrical failure of indeterminant specificity requiring advanced diagnostic workup.

Youtube has several good instructional videos on how to replace the resistor. For example: http://www.youtube.com/watch?v=kikg3uoeNLc
02-06-2011 10:46 PM
Plowboy1970 I too just lost all speeds but high. I could smell a slight electrical smell and thought, what is going???? But I read lots of these forums to know what it is. This forum is GREAT!!!!

THANKS to everyone here!!!!
02-05-2011 02:30 AM
s3nt3nc3d Could be a resistor pack, but I'd check the wiring to the HVAC controls in the dash...often times problems like that are due to melted wiring at the switch.
02-05-2011 01:20 AM
05wrangler
Quote:
Originally Posted by Mikiec View Post
What about it only working on the second speed and none of the others? This is on my 99.

i would pull it out and look at it, its a 20 part and not to bad to change it fixed mine
02-03-2011 07:56 PM
Mikiec What about it only working on the second speed and none of the others? This is on my 99.
02-03-2011 06:44 PM
Loo Replaced this in my 04 last fall. Super easy. Glad I did. I don't like blasting the heat or AC.
02-03-2011 06:17 PM
rtiburon I have a 97 too. Just changed out the resistor/rheostat for the blower last year. Here's a link with pictures. Blower Motor Resistor Install - JeepForum.com Just inside the passenger door under the glove box there's a black plastic kick-stop panel that's kind of a PIA to remove. After that it's a snap.
02-03-2011 05:18 PM
05wrangler right on thanx alot guys, im goin to go get one tomarow, then off to the deeler for that "E05" recall
02-03-2011 05:04 PM
Bryangb7 I just went to the local parts store (advance auto) they had it in stock 20 bucks. I asked for the resistor pack and explained the problem and they gave it to me...two bolts and a plug later I have all four settings
02-03-2011 04:49 PM
docholiday13
Quote:
Originally Posted by 05wrangler
i have a 05 TJ that is doing the same thing, only working on high, where could i get this relay and what is it called?? how would i got about checking the switch selector??
Me to
02-03-2011 04:42 PM
05wrangler i have a 05 TJ that is doing the same thing, only working on high, where could i get this relay and what is it called?? how would i got about checking the switch selector??
08-29-2009 09:51 AM
imowt I have the same proble here as Hondarider... ONLY the high speed is working on my blower motor. I checked the switch selector with a multimeter, and I think the switch is ok..according to a continuity test.
I have 97 wrangler... I har it can be the resistor? Where is it? what does it lok like?
Thanks for your help
jake
07-05-2009 02:40 PM
distortedtj Yep the resistor look like a large relay.. Just unplug the old one and install a new one.
07-05-2009 02:36 PM
Hondarider
Quote:
Originally Posted by Jerry Bransford View Post
It's not a traditional set of resistors like you may be thinking of. In newer TJs, it's more like a credit-card size plug-in which can't be repaired.
Gotcha. I wasn't expecting a bank of axial lead components but I wasn't sure what to look for either. Thanks. I expect it's a pluck and chuck situation.
07-05-2009 11:29 AM
marc1kim The blower resistors are on the passenger footwell right behind the glove box on the blower housing. Mine problem ended up being the blower motor selector switch.
07-05-2009 11:00 AM
Jerry Bransford It's not a traditional set of resistors like you may be thinking of. In newer TJs, it's more like a credit-card size plug-in which can't be repaired.
07-05-2009 10:46 AM
Hondarider Sweet! Thanks for the heads up! That definitely gives me a head start on the troubleshooting. I'll take a look at the service manual and see wherethe resistors are. I'm sure I can check the circuit with a DMM.
07-05-2009 10:09 AM
Jerry Bransford The fan only working on high is normally due to a defective resistor pack. The resistor pack is used for all speeds except for the fan's highest speed where the resistor pack is bypassed. Your 2003 has it in a different location than my '97 does but yours should be somewhere up above the passenger side footwell. It's easily swapped.
07-05-2009 10:04 AM
Hondarider
Blower only works on high...

2003 TJ 4.0 5spd. So the heater fan only works on the highest setting...nothing happening on the other three settings. Blower motor or the switch? Has anyone seen this before? If this is a common failure, it might save me some time on the troubleshooting side of things. Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:26 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC