Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > How to Remove the Grill

Join Wrangler Forum Today


Thread: How to Remove the Grill Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-25-2013 12:03 AM
comptekcs Crawling underneath and twisting the turn signal bulb out makes it easy without having to mess with the tab.

This is a good video for the Truck-lite install and around :40 he shows just twisting out the bulb harness
http://www.youtube.com/watch?v=U8iHO...e_gdata_player
07-25-2013 12:01 AM
Lusus_Naturae ^ You may be able to PM a mod so you can edit your post.
07-24-2013 11:41 PM
UselessPickles
Quote:
Originally Posted by RoadiJeff View Post
There's also a pdf with pics on installing a Metalcrafters grill insert that shows how to remove it.
Looked at their instructions and noticed they say to disconnect the turn signals BEFORE popping the grill off...

That would have made removal/installation a bit more graceful. I wish the forum software would allow me to edit the initial post.
07-23-2013 11:01 PM
sdchickie Thanks for the great tutorial! I'm thinking about having mine wrapped so I would need to remove it for that.
07-23-2013 04:19 PM
dmako Thanks!

Saving for when I replace headlights.
07-23-2013 12:18 PM
par921 thanks for this. i think plastidip or something more permanent like u-pol raptor lining may be in the works for my grill in the near future.
07-23-2013 09:28 AM
RoadiJeff
Quote:
Originally Posted by UselessPickles View Post
I didn't find any nice walk-throughs on how to remove the grill, so I'm making one.
Looks good. There's also a pdf with pics on installing a Metalcrafters grill insert that shows how to remove it.

Metalcrafters Grill Insert Installation Instructions
07-23-2013 08:19 AM
SirRyan This couldn't have come at a better time. I plan on plastidipping my grill tomorrow. Thanks!
07-23-2013 08:02 AM
tupper Thank you for the tutorial...getting ready to take mine off ....had an idea how but this makes things much easier!
07-22-2013 09:14 PM
sunnykk Great write up with pics. My first ever mod when I got my JKU was to install a grill insert.
07-22-2013 08:56 PM
UselessPickles
How to Remove the Grill

I didn't find any nice walk-throughs on how to remove the grill, so I'm making one.

1) Open the hood. This one should be easy. Your owner's manual should have instructions if you're confused.

2) There are 6 plastic fasteners across the top of the grill. They are like reusable plastic rivets. Use a flat blade screw driver to pry the center piece up.





Don't panic if the center piece pops all the way out. It's OK.



With the center popped up, the easiest way to get the fasteners out is to just wedge your fingers under the top of the grill near the fastener and pry up gently just enough to pull the fastener out a little bit. Then you can grab ahold of the fastener with your fingers and pull it out easily.


3) There's 6 clips that snap the bottom of the grill to the vehicle. 4 of them are right along the bottom and can be seen through the grill slits, like this:



Just pull straight out on the grill near those clips to pop them out. The remaining two are on each side, right between the headlight and turn signal, so just grab the top and bottom of the grill right near the head light and pull out.

4) Disconnect the turn signal wiring. This connector has a red tab that you must slide out before you can squeeze and pull.



The turn signal connector and two of the clips are circled above.

5) The grill is now fully disconnected from the vehicle. Set it somewhere safe and continue whatever job required the removal of the grill.


Re-installation should be pretty obvious:

1) Connect turn signal wiring (slide that red tab back in after connecting).

2) Line up the tabs on the bottom of the grill with slots on the vehicle. Press in near each clip to snap them all in.

3) Install the plastic fasteners on the top of the grill. Insert them with the center either popped up or completely removed, then fully insert the center part.

4) Close the hood.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 06:06 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC