|08-02-2013 03:11 PM|
|BCDonny||I like because it is a one simple unit, much higher voltage (really needed in colder weather). A distributor, coil, and ignition module all in one|
|08-02-2013 01:27 PM|
|roadyrob||the HEI is the distributor that should have came in the 4.2 to begin with.|
|08-02-2013 01:11 PM|
Following up on the install.
After timing and idle setting, this made almost as much difference as the Howell EFI upgrade!
Runs like a striped -ass ape! It also looks like (if I can keep my foot out of the firewall!) that it'll get better gas mileage!
Probably the easiest and cheapest upgrade I've done.
|07-24-2013 10:39 PM|
|indirocz28||Just adjust your regular idle screw to idle it up, make sure you hook up a vacuum gauge to a manifold vacuum source, advance the dizzy to where its about 19-20in Hg. (with vacuum advance line off of the dizzy and plugged). You should be pretty close after that.|
|07-24-2013 10:00 PM|
Everything else went super smooth, and it fired up immediately! I gotta wait 'til this weekend for help setting the timing at high idle, but at 900-rpm, it's smoother than a kitten's dick!
I didn't use the 45-degree pliers, just beat up my hand, using the socket and fingers. Would have been much easier without A/C and heater!
Hey, I'll heal, and have a much better YJ for it!
|07-21-2013 03:10 PM|
I refuse to use champion's anymore. I had one come apart one time, and it ruined my engine.
I use copper core auto lites. They have been great. Gaped at .050.
Mine is serpentine too, Thats the trick I use.
The plug should stick in the socket upon removal. Also, put the new plug into the socket, and then start sliding it into the #1 cyl with your right hand, as you reach between the head and a/c compressor with your left and help guide it in.
|07-21-2013 01:47 PM|
I bought Autolites at Auto Zone. $12.00 and got a rebate certificate for a $20.00 Gas Card!
Going back in today; will try the extension and swivel trick. Was thinking along those lines. Once I break the plug loose, I can finger it out with a few scratches on the back of my hand. Same thing getting it started.
BTW, it's serpentine.
|07-21-2013 12:21 PM|
|07-21-2013 08:52 AM|
|roadyrob||just stock copper core champions, but increase the gap to .45-50|
|07-21-2013 07:47 AM|
|Palma11b||What kind of plugs are you guys running to handle the higher voltage with the HEI kit?|
|07-20-2013 05:39 PM|
I had mine done out in 112* heat, no shade, made my own plug wires, and changed all 6 plugs, and re-timed in under 2 hours..
For #1 plug, get a plug socket, 6" extension, and a swivel/u-joint. Go Socket, swivel, 6" extension, ratchet. Easy as pie.
When I put the plugs back in, I pull the extension and swivel off, then reach into the 3/8" inlet on the socket with a set of needle nose's and pull it off.
I use a set of 10" long 45* needle nose to put the plug wires on all the way. Make sure you hear them click.
|07-20-2013 05:25 PM|
|roadyrob||do you have v belts or serpentine? on my 87 with v belts it wasn't to bad just used a swivel and a extension.|
|07-20-2013 04:21 PM|
Had to quit for today. It's 103, with 100% humidity, so the swamp cooler in my shop doesn't do s**t.
One thing, though.... Does anyone have a trick for getting the #1 plug out of a 4.2 with A/C?
You can't even see it. I haven't tried to get a socket in there yet, but it looks tough!
|07-20-2013 01:09 PM|
|Palma11b||Lets us know how it goes! Ill be in the garage....axle u joints are giving me trouble -_-|
|07-20-2013 12:54 PM|
Oops! Just checked again. The gear is metal, but black anodized.
BTW, since I have the Howell TBI kit in, I called them yesterday, and they said that the CRT is perfect for their system. It's what they recommend.
Stand back! I'm going in today, and will report back later.
|07-20-2013 01:34 AM|
CRT has good shit,
I would be leary of buying a GM dizzy from any other company for the 4.2 . Even from reputable places like 4wheelparts. They sell the gm dizzy too, but with a hardened drive gear. Guess what? People have written about them and their crap online and it spreads.
So far, no complaints from me on their customer service. They called me personally when I placed my first order and they were out of stock on the parts to make them.
|07-19-2013 09:35 PM|
|Palma11b||I'm pretty sure the only cam gear you have to worry about is when you take it out of a chevy straight 6|
|07-19-2013 09:31 PM|
I have also heard they are very slow at customer service but get everything fixed.
|07-19-2013 08:44 PM|
|indirocz28||Where are you stationed?|
|07-19-2013 06:42 PM|
|Palma11b||I actually haven't ordered mine yet. I'm going to tonight with all this good feedback. Thanks guys!|
|07-19-2013 04:20 PM|
Where are you stationed?
Right now I am trying to see if it improved my gas mileage any, but yes, more power, better idle and overall running quality, etc.
|07-19-2013 09:02 AM|
|Palma11b||Did you notice any better performance?|
|07-19-2013 08:37 AM|
I put my CRT in last saturday, CRT dizzys won't eat up the cam, they build them all in house.
Their gear is made of METAL not carbon fiber. However it is softer than the cam. Also, the distributor body is made of billet aluminum and its a very quality piece.
I love mine so far. Make sure you get their plug wires, or else you'll be making your own.
|07-18-2013 04:01 PM|
|Palma11b||I was concerned about the camshaft getting eaten up but if its made of carbon fiber it shouldent! Let me know how you like it after install? I'm gunna order mine this weekend. Thanks!|
|07-18-2013 03:52 PM|
|Fredzo||I just received my CRT yesterday, and it looks like the camshaft gear is made of carbon fiber, so it can't chew up the camshaft gear. Gonna install it tomorrow. Already have the Howell TBI set up, so this should make it even mo' betta!|
|07-18-2013 03:27 PM|
|Palma11b||Alot of people were saying they had problems with the MSD ignition module ot something...haven't really looked into it. Did the CRT distributor mess up your camshaft?|
|07-18-2013 10:46 AM|
|BCDonny||I also use the CRT HEI very happy with it like said before also get the wires with it.|
|07-18-2013 10:33 AM|
the HEI from CRT is very popular. I've had mine for 5 years with great results. be sure to get wires too, the 8mm wires are needed with the hotter spark. if money isn't important MSD is probably the best setup but a complete system will cost around 700.00
stay away from the cheap HEI's they are junk.
|07-18-2013 09:10 AM|
CRT Performance HEI kit. Any good? other options?
So ive been doing a bunch of research on HEI conversions for my 90 4.2l People all have opinions on MSD, DUI, putting a Chevy distributor in from a 250. I found a company called CRT Performance that makes the HEI distriutor and wires for 150. Not bad. Im looking for some facts. Which is better? Reliability? Everything helps!