|03-27-2014 11:37 PM|
|bobbowtie||hopefully do a v8 swap someday|
|03-21-2014 12:43 PM|
That looks good , I'm considering scrapping my idea and going this rout. Did you go with the 4-speed manual trans ? And do you know if I could use the 700r4 auto if my wife decides she don't want to shift gears...
95' with 05' Motor and trans,,,
|01-23-2014 04:52 PM|
|AZ_YJ_4.0||I recommend Novak they made my 6.0 swat seem less motor mounts are solid and the transfer case adapter as well. I pulled a 6.0 motor from a 2000 Yukon Denali and the trans off of an 85 Chevy Blazer) set the computer to manual trans) in this case and kept the NP321 T-case off my YJ it's a very very simple swap. You can get gauges from Autometer or their cheaper version Auto Gauge and will work great. Biggest issue I ran into was alining the t-case out put to the front diff it's just a matter of olaying with the engine location. We set up the engine about an inch to the right from the center. It been running perfectly fine for about a year and a half. Like all these guys say, take your time and do your homework.|
|01-19-2014 12:47 PM|
Well first off road journey with sbc in jeep went pretty good!! Lol last day of duck season today, an didn't have a 4wheeler, so I decided to go pick up my duck an goose decoys in my jeep!
I would def have to say, a v8 an 34" superswamper's are a plus!!! Still don't have 4x4 hooked bk up yet but didn't need it!
|01-07-2014 06:35 PM|
|CAJUN YJ||I switched to a jeep in tank pump. I used the pump for a 91 wrangler.... It is a direct fit into my tank. So far so good...... It has plenty of flow for my needs.... But my v8 is a stock 95 TBI....|
|01-05-2014 01:23 PM|
|12-31-2013 08:23 AM|
An here is my new 8.8 out of a 96 explorer that had only 94k mi on it..... Not bad for $103.11!!!! An 3 hrs of my time!!!
|12-31-2013 08:20 AM|
An this past Sunday, I finally decided to go run to pull a part an get me a 8.8 rear..... The d35 is on it's last leg now that my new Swamper LTB's r on....
|12-31-2013 08:19 AM|
Well guys, sorry I've been off for a while.... Been very busy with my two new lil girls... Dam twins can b a hand full!!! Lol
Update to my sbc swap....
Had to swap out jegs fuel pump an go to a factory style intank pump... Now motor runs very good with no spit an sputter.
Since I've changed fuel pump an sender, had to swap all gauges to mk them match fuel gauge I installed for new sender...
|11-06-2013 09:30 AM|
|10-24-2013 08:47 AM|
Well just about got the inside of my jeep just about wrapped up, just need to order a new brake light switch an wire it up, an the electrical will be complete!!! I do have a feeling that the ol 35 rear end prob won't hold up too long, but I think ill just swap in an 8.8. Besides a few wires to hide an my speedo to hook up an program, I'm 97% done!!! It's well worth all the time and money!!!!
|10-12-2013 12:48 AM|
I ended up putting two 30" cherry bomb glass packs. I like the "ol school" sound an it's not that loud an actually pretty quiet at hwy speed. But, when I down shift an mash out, u def know that they are there!! Lol
Hell they were cheap! 31$ each with tax an I did all the welding myself!
|10-10-2013 10:27 PM|
|WICruiser||Great job, I wish my project was any where near that far along.|
|10-10-2013 06:12 PM|
|TexasDemon84||Congrats!! Looks great. Boy those 350s sure sound great. I told the guy that did my exhaust I just wanted a good muffler not real quiet not too loud. I don't want no Flowmaster or such. I go to pick it up sounds great. I get home look under Jeep, he put in a stainless Magnaflow.|
|10-10-2013 11:46 AM|
New update.... Got all exhaust piped in an hung. Now I just need to wire up my headlights an brake lights, and blinkers... Then it will finally B road legal lol.
I can say one thing, this is a whole new animal! It's 5 times the motor that was in it from factory, an it's nice to hear a lil v8 rumble in it!!! Wow is all I can say!!
Just need to paint exhaust black to match frame.... Can't leave it red with a blue jeep lol.....
|10-05-2013 09:32 AM|
Well finally!!!! ) ))!!!!
I started piping in my exhaust last nite after work, got one side done. Just need to finish the passenger side, an the blue machine will be ready to drive out the shed!!!! Woohoo!!
After that, it's just a matter of checking all connections for leaks, re installing my tach an speedo, front fenders, an wiring up my headlights an blinkers!!! Finally so close!!! ) ) ) )
Just hope that two 30" cherry bomb g.packs won't piss off the neighbors......... )
Ill post pix today after I get off of work later!!! So dam excited!!!
|09-27-2013 12:37 AM|
That's how I had measured first, which gave me my 17.500" length.
Then I called to have a shaft built here locally, an they told me to measure ctr-ctr of Ujoint caps. Which factory is 13.250", and my need is 1.500"-1.625" longer. The factory auto tranny shaft is 14.875" running length. So I'm thinkn that it will b pretty dam close!!! Got my fingers crossed!!! We will find out tomorrow after work as my new shaft will b waiting when I get home!!!!
|09-24-2013 11:17 PM|
|indirocz28||Try the shaft, but you need to measure from the center of the rear yoke up to the tail housing, then add the length for the slip yoke of how far it sticks inside.|
|09-22-2013 11:00 AM|
I've actually robbed some hoses off of the truck I had bought to do my swap. I robbed two hoses off the truck, the I just cut off the xtra length I didn't need.
The only other option I had found was to get some universal/custom cut to length hose. But it was expensive. So I took the cheap route for now. Lol
|09-22-2013 06:16 AM|
|kywaterman||Not sure on the answer for your question, but I have a question for you. What is the part number for the radiator hoses your running? or what application were they originally for?|
|09-21-2013 08:39 PM|
|CAJUN YJ||Hey guys, I've got a question about my rear driveshaft. I'm needing a shaft that is real close to 15" running length.... A stock length yj shaft for a auto tranny is 14-7/8" running length... Do you guys think I could run that shaft??? I've got a buddy with a parts jeep yj, with an auto tranny. Said I could have the shaft..... But want to mk sure it will work|
|09-17-2013 07:25 AM|
Yea gettn real close finally! I was able to start it an let it run for a lil while. Wanted to mk sure that I had no coolant leaks, or oil leaks. Now all I go left is to bleed clutch, drain an clean tank, an build my driveshaft at work, then I should beable to take her for a spin!!!
Wish I could post a short video, she sounds mean!! Lol
|09-16-2013 02:13 PM|
|kywaterman||Congrats man! Glade to see your about done|
|09-15-2013 09:24 PM|
|indirocz28||Congratulations!!! It will be well worth it!|
|09-15-2013 02:47 AM|
Well finally!!! Woo hoo!!! Got my cooling system Finally in an piped in, fuel pump wired an piped. Now just need to drain the dam tank again......;/
Shitty, crappy, junk ethanol fuel.....
But, before I drain the tank, I think ill just put a jug of gas underneath an prime up pump to ck for leaks........ An of course push the start button!!!!!!! It's still open header but it will b ok to run for 5 min r so.... Lol ready to hear it run!!! Sob it took a while, but I think it's well worth the headache!
Now just need to bleed clutch, measure the length for new rear drive shaft, build it at work an have it balanced, then finish wiring up gauges in dash, an ill finall beable to drive it outta the shed!!! Dam excited!!
|09-12-2013 08:35 PM|
|indirocz28||I know the feeling. I had a day off today and spent all day re doing my exhaust, and putting in a new Prothane transmission mount and re- checking all the bolts from originally installing my lift kit.|
|09-11-2013 08:28 PM|
|CAJUN YJ||Thx man, i need the encouragement lol, I'm getting kinda frustrated with the whole thing. I'm so busy with work an stuff, I barely have time to turn a wrench anymore.|
|09-11-2013 12:38 PM|
|indirocz28||Great! Best of luck!!|
|09-10-2013 08:17 AM|
|CAJUN YJ||Well, the correct radiator an new intake will be here today! So finally, ill beable to start an let it run for a bit. Hopefully at least!! Ill post pix of my dash an stuff later tonite!|
|08-30-2013 10:45 PM|
|CAJUN YJ||Thx man! I know exactly what you mean about the life stuff!! Lol with two lil ones on the way, I'm about to get a big kick in the ass by life! Lol|
|This thread has more than 30 replies. Click here to review the whole thread.|