Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Thinking about getting a longer driveshaft with no SYE

Join Wrangler Forum Today


Thread: Thinking about getting a longer driveshaft with no SYE Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-26-2006 05:53 PM
Jerry Bransford
Quote:
Originally Posted by Hank View Post
So I guess just getting a longer drive shaft and taking out the transfer drop kit won't work?
No, nothing changes just because you asked again.
12-26-2006 04:10 PM
Hank I'll have access to plenty of tools. I put my lift on and I do all of my maintenance at the Ft Meade auto hobby shop. It's a pretty nice setup. They have all of the tools and lifts I'll need. I was just trying to avoid doing the SYE for money reasons and time. So I guess just getting a longer drive shaft and taking out the transfer drop kit won't work?
12-26-2006 04:07 PM
Jerry Bransford A longer driveshaft installed on the OE transfer case output shaft's slip joint will only be longer... the u-joint angles will be identical so there would be no benefit to the longer driveshaft if installed by itself.

The only way to achieve a lower driveshaft angle (and consequently a reduced u-joint angle) is to either cut the OE t-case output shaft off together and install a "hack 'n' tap" kit from Rubicon Express, or install a full-blown SYE kit. Either of those would move the front driveshaft mounting point forward which is what lowers the driveshaft and u-joint angles.
12-26-2006 03:26 PM
MR.CLIFFORD It really depends on your level of craftsmanship. To me, a SYE isn't all that difficult and I can finish one out in a couple hours. It will take more time if it is your first time. There are tons of write ups to guide you through the process. You also need some specific tools that you will probably have to buy. I bought a decent set of snap-on snap ring pliers. They are a must.
12-26-2006 03:10 PM
Hank I don't have any vibes right now. I was just trying to increase my clearence. I was looking at the shafts from Tom Woods. If I can talk my wife into letting me sink $500 more into the jeep, how hard is it to install a SYE?
12-26-2006 03:07 PM
MR.CLIFFORD Hank,

If you want to save money and time then do it the right way the first time. The length is not the issue. It is the angle of the joints. Leaving the tcase drop kit in is your best bet besides a Motor Mount Lift which, in most cases, won't get rid of your vibe. A SYE and double cardan drive shaft is the best, do it once do it right, option.
12-26-2006 03:04 PM
Hank
Thinking about getting a longer driveshaft with no SYE

I have a 4inch Rough Country suspension lift with a transfer case drop bracket. I'm thinking of just getting a longer driveshaft to eliminate the need for a drop bracket. I know that the best way would be to install a SYE with a new shaft, but I'm trying to save some money and time. What do yall think of me just getting a longer drive shaft made and taking out the drop bracket instead of installing a SYE with a new shaft? Will this even work?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 07:29 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC