|08-08-2009 02:35 PM|
I hadn't looked at the ECU /wheel speed box connection too closely. I would have to have an understanding of the signal passing through that wire to know how that half of the switch works. The mod he posted was a diagram from some other forum he added the locker switching modification according to his post. Now just looking at that side of the switch from a logic standpoint without defining the signal travelling on the purple with light blue tracer wire, if that is normally connected without the switch, then it would make sense that disconnecting it would modify the signal and prevent the ESP from activating (I'm speculating). If that is the case, then you would want that open when the lockers are forced to the locked position. That would actually require a double pole double throw swtich DPDT. With the double pole single throw switch DPST that he has depicted, it looks like the ESP would be off while the lockers are not being forced to lock and ESP on with the lockers locked.
I'm pretty sure that you would want to make the other side of the switch to be open when the lockers are forced on and closed when the lockers are not forced on. So basically when the locker side of the switch is open, the ESP side should be closed. and when the locker side is closed forcing lock, the other side should be open preventing ESP from coming on. Again, that would require a double pole double throw type switch that has two positions on/on, they do make a three position switch on/off/on. On the three position switch, the common is not connected to either side when in the center position and that would not be required in this application.
Now, I hope I haven't totally confused you.
|08-08-2009 12:19 PM|
|Codeman911||Jk'n, lookin at that diagram I wonder why you would have to tie into the ecu and the wheel speed box? Couldn't you just run a wire to the relays like you have shown and then hook you toggle to a power wire that's hot with key on so any time you flip the switch they lock?|
|08-07-2009 06:03 PM|
|jk'n||Someone posted this thread a while back. As you will be able to tell if you read the whole thread, there was a discussion back and forth as to the need to isolate the two outputs with diodes but generally speaking, I think the circuit would work either way. Just without the diodes, the front and rear would not be able to be operated independently like the factory provided circuit does. If you try the mod, let the forum know how it works out.|
|08-07-2009 04:54 PM|
So in 4 hi,, they dont lock up,,, are they limited slip thou?
4 low is like what ,, upto 10mph? You can get a rear locker on a X model,, and I think Sharaha has front and rear too...
I hate it when only one wheel spinns when u get on it. and or need both.
|08-07-2009 04:41 PM|
|Codeman911||I see now. Not what I thought it would have been but I see now! Thanks for the pic Bro! I'm gonna do some looking for that hack!|
|08-07-2009 04:07 PM|
|08-07-2009 03:50 PM|
|Codeman911||Any way to get them to lock up in 4H? Plus, where do the sway bars disconect? I looked under there and I don't see any actuators or anything like that. They look like sway bars to me.|
|08-07-2009 03:47 PM|
|N39-W120||If you are in a real hurry you can download here. Also the lockers will only engage while in 4L, then they will be solid|
|08-07-2009 03:03 PM|
|SpeedJunkie||Sway bar disconnect is just the front. The lockers are electronic and locked when you engage them.|
|08-07-2009 03:02 PM|
|08-07-2009 03:01 PM|
How do the lockers on a Rubicon work?
I just picked up my first Jeep yesterday and I'm still grinnin' ear to ear! But it didn't have an owners manual, so I ordered one on ebay. But I am impatient and am not sure of a couple things. The electronic sway bay disconnect on my 07, is that front and rear sways? Also, when I hit the locker button, the front and rear lock symbols just flash on the dash. Does that mean they are locked up? Any info will help. Thanks!