Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > 99 Blower motor issue...HELP

Join Wrangler Forum Today

Thread: 99 Blower motor issue...HELP Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-12-2012 04:41 PM
davefewox it appears that the horn and a/c relays are the same , swap them temporarily. also ck fuse 8 at fuse block and fuse 11 under hood in pdc
09-01-2010 04:18 PM
FrankieT My a/c blower motor does not work at all and after checking my switches I found I have no power at my on/off/selector switch and at my speed control switch. Is that a relay issue? If so how can I test the relay to tell if its bad or not?
01-08-2010 05:06 PM
Jerry Bransford +12v on both leads of the motor means it's not being grounded on the switched lead which means it won't run. One side is feeding the +12 to it and you're seeing +12 on the other side through the motor's coil inside. When the other side is grounded via one of the resistor pack's low/med/high speeds through the switch, it'll probably run. At this point I'm thinking a bad cable or perhaps a bad switch.

Think of providing 12 volts to one side of a bulb but not grounding its other side. The bulb won't light, you'll measure 12 volts on both of the bulb's connectors since the bulb's filament is conducting the 12 volts through to its other side. Ground the other side of the bulb and it will light up.
01-08-2010 04:55 PM
blower motor troubles 2000tj

ive replaced,switch,relay,fuse,,,still nothing,,,but why would i have positive [hot]reading on BOTH wires going to motor,instead 1 hot 1 neg or nothing on both??is this what happens if resistor is bad?was working fine,then i turned down the speed it went down as i turned it never came back on,,this is the second new switch ive tried
08-09-2009 09:41 PM
jpdocdave pretty easy, back probe the power and ground wire at the motor. if you have power and ground at the blower motor, and its not blowing, you need a new blower motor. if power isn't there, then its not the blower motor.
08-09-2009 09:39 PM
cummings145 I can feel/hear the relay pull in and the A/C Clutch kicks can I test the blower motor?
08-09-2009 09:33 PM
wbrett1027 hey, maybe the relay is bad, fuses? check for damaged wires..
let me know
08-09-2009 09:26 PM
99 Blower motor issue...HELP

I've got a 99 Wrangler where the blower motor for A/C and Heat doesnt work at all. I replaced the fan speed switch, no luck. Bought the blower motor resistor today, nothing still. Anyone with some help...I dont need a/c but my wife does!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 04:01 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC