Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > frame rot question

Join Wrangler Forum Today


Thread: frame rot question Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-28-2009 04:29 PM
Gaducker
Quote:
Originally Posted by scrambler1 View Post
You gotta love vermont rust,thats why I travel south to get my jeeps way cheaper in the long run. Rust never goes away.


I am proud not to have to deal with that kinda rust, but it sure is hot down here.
08-27-2009 07:19 PM
scrambler1 You gotta love vermont rust,thats why I travel south to get my jeeps way cheaper in the long run. Rust never goes away.
08-27-2009 10:29 AM
morphious depends on what u need, most of the time the frame only rots on the bottom and side. u seen how bad mine was but the tops were mint. but with how bad urs are not u could probably just patch them with a little wielding work and they would be fine for what u use it for
08-27-2009 08:41 AM
Moojamboo that pic I posted of the replacement frame insert, it looks like it is three sided...shouldn't it be 4 sided to match up with the original frame?
08-26-2009 11:19 PM
morphious thanks birdhunter i was looking for that these guys are a little cheaper if i remember right
08-26-2009 11:17 PM
birdhunter DaveysGeeps.com has some frame rails
08-26-2009 11:10 PM
morphious ok welcome to the my frame hates me club take a look at mine
it does look like u can drive it but i ended up weilding 3/16 plate steal into the frame
08-26-2009 10:43 PM
uplifted Thank you for the link... very cool... Thank god mine are soilid enough to not need them at this point..
08-26-2009 10:03 PM
Moojamboo I found them here:

Auto Rust Technicians

For 125 it doesn't seem to bad, so long as you can get it done.
08-26-2009 09:27 PM
uplifted Please inform me where to find those?? i searched and searched but could not find any kind of jeep frame repair pieces..... Where did you get those?...................As far as your rot, the guy who sold me the jeep drove it like that without any problems...how long will it last,, who knows..
08-26-2009 07:20 PM
Moojamboo thanks for the reply,

would I be better off just cutting out the problem area with something like this:



Either way, does it look safe enough to drive on for the duration?

thanks
08-26-2009 07:06 PM
uplifted I just had to deal with the same exact rot you have except on both sides... I ended up welding in plates from the rear bumper lower bolt hole and ran the strip of flat stock about a foot up towards the front of the jeep.. Welded the entire length down both sides and then plated both sides of the frame and tied the into the same bolts that hold the bumper on...All in all i would suggest dropping the rear bumper and fuel tank so you can really lay a good solid weld on the flat stock you'll be adding........ The down side is, eventually it will come back as it rots from the inside out...
08-26-2009 05:12 PM
Moojamboo
frame rot question

Hi all,

As I was dealing with a tailpipe issue, I noticed I have some frame rot on the back right of the frame, at the rear shackle. It looks like:



I took a hammer to it and there is some more rot up from the hole, and a little behind. There doesn't seem to be any major problems on top of the frame, just the bottom (a little on the side).

As someone who is just learning about tinkering with vehicles, what do I do? I have done some research about doner frames, but this is above my finances and I have no welding knowledge/equipment. I have read about some solutions that seems to put more metal around the problem area - but how will this work if the issues is right where the shackle connects to the frame?

I am hoping this is less of a problem because it is on the bottom compared to the top? This problem is not on the other rear side of the frame, just the right rear section.

This Jeep is an April to October driver only, and I would be surprised if it did more than 1000-2000 miles a season (from now on - I just bought it this spring) I don't go crazy off roading, maybe some class 4 roads once in a while...I really just wanted summer jeep to take the dogs to the river and bum around town when its nice. Lots of dirt roads.

I am looking for suggestions, hopefully not super duper expensive, and hopefully not "scrap the jeep". Anybody had a similar experience?

Thanks,

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:16 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC