Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ General Discussion Forum > axles

Join Wrangler Forum Today

Thread: axles Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-12-2009 10:21 AM
morphious yeah it was one of those ideas i had sitting in the garage on my chair looking at the jeep and the old burban out back. its probably just to much work but on that note as far as wide goes I'm used to a full sized k5 with 12.5 tires. so the jeep seems too narrow, but with that said i also can make it through quite a bit of stuff with it. so i dont know i'll hold out for awhile for a good set of dana 60's. a guy up the road from me had some under his cj7 and it looked wicked with those and 39's on it.
09-12-2009 08:07 AM
buckshot500 I have been thinking about trying to get some Chebby D60's.
I read that it's possible to adapt a D-300 t-case to an AX-15.
This would give me the passenger side drop.

Personally I wouldn't go through all that for D44's though.
A front D44 is only marginally stronger than a D30.
09-12-2009 01:30 AM
tbeede its going to be wide and you're not really going to get a big step up in axle beef... yeah they are heavier duty but not by enough for the work... think about all the other issues like wheel bolt pattern, steering, etc... etc... this is the type of idea that sounds like fun when ur drinking beer and snowballs into lots of time and money before you know it and the results might not have been worth it depending on what you're looking for...
09-10-2009 10:42 AM
morphious well i wasn't going to do the rear 10 bolt but yeah. I'll probably just have to figure another way to get me some full sized axles. i really want to do spring over conversion but i want to put full sized axles under their so its all done in one shot.
09-10-2009 10:29 AM
whitebuffalo like i said (and a couple others) there'll be a lot more work than its worth to swap in a 10 bolt
09-10-2009 10:22 AM
morphious ah crap i forgot about the wrong side transfer case problem well now that just complicates it a little more don't it
09-10-2009 10:19 AM
whitebuffalo dont older chevy's use the push/pull steering setup? if they are, you'll need more than just a drop pitman arm. and werent they still passenger side drop in the mid-80s? if so, you're gonna need a new transfer case as well.......
09-10-2009 07:20 AM
morphious yeah i am probebly just going to buy rear axle for it if it comes down to it
09-09-2009 09:04 PM
Pylonpounder If it helps, I believe 72 suburbans, and those of the same generation as the 72, have 14-bolt rears..
09-09-2009 07:27 PM
morphious oh i wasn't going to replace the rear with the 10 bolt i was just excited for the dana 44 was planing a 14 bolt or maybe just a 12 i don't think i will need a 14 but then again bigger is usually better
09-09-2009 07:20 PM
4Jeepn The 10 bolt is the dana 35 of the chevy world.. don't waste your time and energy.. Go find a 14 bolt for $300 and be happy with life.
09-09-2009 07:15 PM
morphious so on a update i found a 10 bolt in the rear and a dana 44 up frount on the old burb it least I'm pretty sure that's what it was so the biggest hurdle now is getting my old man to let me tear her apart for the axle but my question now is if i put that under my jeep i know i need a drop pitman arm but what else (other then sye)
09-08-2009 12:53 PM
morphious well the chart says the dana44 and the 10 bolt run the same ring gear size and does spline count matter that much i mean i have dabbled in axle stuff before but only to fix things and i think its only a few short of the 44 spline count
09-08-2009 12:45 PM
whitebuffalo small ring gear, 28 spline axles, etc.
09-08-2009 12:15 PM
morphious ahh ok well if anyone else had anymore info that would be awesome but i'm curious what was weak on them the axles or the houseing ? i just want to be sure that in the end i wont regret this
09-08-2009 12:03 PM
whitebuffalo from what i've heard, the 10 bolts were on the weak side. someone else should probably chime in on it though. it might not be worth the trouble of swapping in full widths for a pair of 10 bolts.
09-08-2009 11:56 AM
morphious ok yeah i think ur right on the 10 or 12 that's what i think they looked like now how good are they in comparison i know their probably better then the dana 35 under their right now but in terms should i hold out for a dana 44 or would these work OK for what i want to do
09-08-2009 11:17 AM
whitebuffalo rear could be a 10 or 12 bolt. the front is probably a 10 bolt (assuming its a half ton 'burban)

Axle Identification Chart
09-08-2009 11:05 AM
morphious well i would but their at the shop and i'm twenty miles away from em any guess what they would be
09-08-2009 10:45 AM
whitebuffalo post up some pics of the pumpkins
09-08-2009 10:08 AM

ok so I'm thinking about doing some fun stuff in the next couple of days. but i need to know i have a old 85 chevy suburban 4x4, what axles are under it i looked around but found nothing on this. i would like to put the axles under the yj with a soa and maybe eventually even the motor but i dont know if those are the dana44's or not. i know their not 60's for sure but i want dana 44's any help with this would be great.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 01:43 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC