Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ General Discussion Forum > Upgraded tires to 31's, now gearing issues

Join Wrangler Forum Today


Thread: Upgraded tires to 31's, now gearing issues Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-03-2005 04:54 PM
1BLKJP
Quote:
Originally Posted by willness33
The adapter is Spicer 2-2-1397 for about $35. The flange bolts needed are Ford P/N n800594-s100 for about $1.50 x 4.
The bolts are a dealer only item (at least out here in AZ they are) The flange we got from M.O.R.E along with the bracket kit.

Your also going to need 2 passenger side soft brake lines and some hard line to hook all your brake gear up. Unless you have the 8.8 with drums and then I believe it will all bolt right up.
11-02-2005 11:19 PM
87wranglerguy Thanks, beside the adapter, do you know what if any other additional items I might need to make the swap? I would rather have all the items on hand at the time of swapping.
11-02-2005 12:57 AM
willness33
Quote:
Originally Posted by 4Jeepn
I also recall something about the rear driveshaft to axle yoke/flange needing an adapter.
The adapter is Spicer 2-2-1397 for about $35. The flange bolts needed are Ford P/N n800594-s100 for about $1.50 x 4.
11-02-2005 12:51 AM
willness33 Ranger and Mustang 8.8s are 28 spline axles. Although not ideal, they are still marginally stronger than D44 shafts. They do not have disk brakes which would be a major improvement over the jeep drums.
11-01-2005 05:19 PM
1BLKJP
Quote:
Originally Posted by 87wranglerguy
thanks for the info. Regarding the 8.8...I have an 8.8 from another mustang. How difficult is it to make the changes ie..any welding or modicications to the rear end?
thanks
I'm having a hard time remembering without looking somewhere else, but I don't believe the Ranger or the Mustang 8.8's are 31 spline.
10-30-2005 11:15 PM
87wranglerguy man, this site is great! thanks for providing me the info. Now I just hope that I don't run into any problems when I return back to the states to begin my project.
10-30-2005 08:20 PM
4Jeepn Lots of good write up's on the 8.8 swap.. some welding, but for the Yj it should be less than the TJ. The one thing you may wish to check on is on the width of the stang 8.8's. The one's I have seen swaped over came from explorer's which are just about the same width as the stock rear but feature 31 spline shafts, which are nice. I also recall something about the rear driveshaft to axle yoke/flange needing an adapter.
10-30-2005 07:51 PM
87wranglerguy
31's but what gearing

thanks for the info. Regarding the 8.8...I have an 8.8 from another mustang. How difficult is it to make the changes ie..any welding or modicications to the rear end?
thanks
10-30-2005 07:22 AM
4Jeepn 1st thanks for the job you are doing. 2nd as for gears, I have heard a lot of the 2.5 guys go with either 4.56 or 4.88's,but that is with the 5spd and 33's.You should have 4.11 right now.

As for a locker all kinds of choices. First decide how much you want to spend. There are full time lockers, which are always on, and others that you need to push or pull a button, via, air or cable, or electric. these of course cost more. The other factor to consider is your rear axle, which should be the dana 35. When you start going to bigger tires, lower gears and lockers in that axle, it tends to cause issues, with the smaller axle shafts it has. thus I have seen stock one's with a locker and 31's break, and stock one's without a locker run 33's just fine. There are several kits on the market that include upgraded axle shafts and a locker to beef up this axle. Some folks will put a dana 44 or ford 8,8 in the back, as these feature stronger shafts and other components. Lastly, a full time locker either in the front or rear axle, can make the jeep drive different than you or your wife are used to. I had one in the front along with some 33's on a snow covered road, and I put in back in 2wd to get home as it kept pulling me into the other lane. Thus read up some more, talk to some more people and go from there. As for names of lockers, there are ARB air lockers, detroit, lock-right, ox, to name a few.
10-30-2005 06:15 AM
87wranglerguy
Upgraded tires to 31's, now gearing issues

Hey folks,
hope you can help me out here. My wife had just upgraded the tires to BFG 31 AT's and my 87 Wrangler is a 2.5L. In order to maintain a decent speed down the highway, what gearing do you recommend? Also, I wish to install a locker for my occasional jaunts in the mountains. I have read a little about them in the circulating mags, but still am a little nervous in making the purchase. Can you jeepers recommend what to buy?
thanks a bunch.
Oh by the way, I am in Iraq until November and hope to be back in action soon.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:16 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC