|11-06-2013 05:18 PM|
Thanks all for the info! Had some issue removing the old gasket, but as soon as I got that done, everything went smoothly.
And yeah, there was just enough room behind the fan to work.
|10-31-2013 08:47 PM|
I got the OEM which already has the hole with a brass one-way valve in it.
Everything's still functioning very well with the cooling system.
|10-31-2013 08:41 PM|
|SpaceCase||Haynes repair manual is the way to go. Can get them at Canadian Tire, not sure where in the states though.|
|10-31-2013 02:39 PM|
|hambubba||You can overtighten the housing until it cracks. "just tight enough" is the rule here - really snug. You have to check it for leaks when you start it up, but tightening and hearing that "kkkkkk!" sound? Been there a few times.|
|10-31-2013 02:03 PM|
|bardb||I don't recall removing anything other than the hoses and the two bolts. But you'll figure it out in short order.|
|10-30-2013 04:56 PM|
Bardb- that's the video I've found. It looks like he's already taken the fan off, or there's more room than I think there is..
hYJacked- I agree! I'm on the lookout for a cheap one, but until then, gotta use what I can get to! :-)
Thanks for the response both of you!
|10-30-2013 03:36 PM|
|valentine1210||My 2003 2.4l seems to be staying around the first smaller dot on the gauge maybe a little higher but normally she is right at 210. Now that it's winter I figured it was just the colder weather but could it be that my thermostat is stuck open|
|10-30-2013 03:33 PM|
|hYJacked||Also probably worth investing in a DIY repair manual if you are serious about educating yourself. Youtube is great and all, but can't always replace a professional manual.|
|10-30-2013 03:23 PM|
How To Change the Thermostat in a Jeep Wrangler - YouTube
Pretty straight forward. The replacement in the video didn't use a bleeder hole and didn't mention torque specs other than 'tighten to mfg specs'. Not sure on your Jeep, but my 99 is spec'd for 15 ft/lb. Mine loosened after a couple of drive cycles, so check it regularly until it no longer backs off.
|10-30-2013 10:17 AM|
I'm having what seems to be the same problem with my '01 Wrangler. Temps low, lukewarm air blowing.
I'm starting to teach myself how to take care of my own vehicle, and am uneducated. So the question is- How do I get to the thermostat to change it? It looks like I need to remove the fan behind the radiator, But I'm not sure. The videos I've found online conveniently skip that part...
|09-11-2013 11:53 AM|
Just a quick follow-up.
Success! Thermostat was indeed the problem. Upon replacing it temps have returned to normal.
|09-10-2013 06:04 PM|
Just got the OEM in and this is what it looks like. It has the hole with a passive brass pin going through it. I'll install it here shortly.
|09-10-2013 05:02 PM|
Pretty sure I'm paying a $10 delivery charge as part of the $22 for the OEM, I expected that.
really no big deal
|09-10-2013 03:51 PM|
Where I live these exact same parts are dealer $13 and parts store $15. I wish they would be more consistent in their pricing...
|09-10-2013 03:47 PM|
|09-10-2013 02:54 PM|
|Big Sarge||yeah I would have not paid the $22. All you need is a 195 t-stat and drill the hole like this|
|09-10-2013 02:48 PM|
I went to the local Carquest and they had two thermostats in stock. Both Carquest brand and 195 degree. One was listed as "economy" and cost about $4. The other was listed as "premium" and cost about $8. Neither had the hole and they both looked identical.
So... their parts guy was already on the road down in the front range (Denver area) and I had them add an OEM Mopar thermostat since he'll be going by the dealership today.
$22, that's expensive. It'll be here in a few hours.
|09-10-2013 01:59 PM|
|09-10-2013 01:58 PM|
I'm about 70 miles and two mtn passes from the nearest dealership.
I guess I can have Carquest order one from a front range dealership if it's that big of a deal. They have guys that run down the mountain every day for OEM parts. Will probably cost more and have to wait a day though.
|09-10-2013 01:56 PM|
|Big Sarge||a 1/8" hole can be drilled into any thermostat that does not have the burp hole. Stant is a very good choice.|
|09-10-2013 01:53 PM|
Do not get a parts place thermostat. I have yet to see one with the bleeder hole. Go to a dealership. Mine (last week) was actually two bucks cheaper than the one I bought (and returned) to AutoZone. (The AZ one lacked the bleeder hole.)
The bleeder hole needs to be there, and it needs to be oriented at 12:00, straight up.
And it *must* be a 195║ model. So if you find a parts store thermostat for our beloved 4.0L engine and it has the bleeder hole, do not get one that is "high performance" or that opens at 185║ or whatever. 195║ only! ;-)
This is a part of a critical engine system, so just get OEM at the dealer. It is not expensive at all. However, they might have to order it. They have to order just about everything for my 2003, of course, but actually had the thermostat in stock. Maybe the JKs use them, too? Hmm...
|09-10-2013 01:37 PM|
|Gold Miner||That's what I'm thinkin'. Good place to start anyway... Carquest brand thermostat acceptable? Or is there a magic thermostat brand out there that we all like to use?|
|09-10-2013 01:28 PM|
|Imped||My first guess was the thermostat is stuck open. That sounds like about the right temp for that as well.|
|09-10-2013 01:19 PM|
Running Too Cool All Of A Sudden
2002 4.0L, Auto, 3sp
Normally runs at 210 or just over the 210 mark.
Today she won't get warmer than 150-160 (according to the dash gauge).
No CEL, will blow heat, no other symptoms... running well.
Coolant system full, sealed, and burped.
I'd like to nip this in the bud.