Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ General Discussion Forum > 88 jeep yj rearend ???

Join Wrangler Forum Today

Thread: 88 jeep yj rearend ??? Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-11-2009 12:19 AM
cn.anglin put the new spider gears in today. on the axles with the roll pin all you do is remove the main carrier caps and then you can get a 3/16 punch in there and tap the pin back enough for the center pin to slide out. turned out to be much easier than i thought. drove thed jeep around the yard but will take it on the road later to see if all else is good. if the transfer case is bad would it still move under its own power like it is and what can i expect if it bent the shaft in the t-case?
10-09-2009 08:41 PM
RednekYJ I think 89 was the last year of the non C-clip D35. The obvious tell is 10" drums rather than 9".
10-09-2009 08:35 PM
cn.anglin yes it is a bearing retained axle. all of them in the 80's were
10-09-2009 08:33 PM
jeep rearend

yes the transfer case was in neutral and so was the 5spd tranny. i was doing about 70 when the road dipped and i heard the bang. the transfer case still works when you put it in 2wd [ rear output turns] and when put in 4wd[both ends turn]. unable to tell if it will pull the front until my new driveshaft gets here for the front. it did no damage to the rear driveshaft .
10-09-2009 07:49 PM
95riogrande Wait how can the axles come out with the center pin still in? Is it a bearing retainer or a c-clip style?
10-09-2009 07:28 PM
buckshot500 Flat towing it with the t-case in neutral & the transmission in park-auto, low gear-manual I hope!

Either way, take 4jeepn's advice & take a good close look inside the T-case.
I'm thinking the T-case locked & twisted the front shaft & shock loaded the rear spiders.
10-09-2009 01:19 PM
4Jeepn not sure on the pin issues. However You might want to look over the case really well, or even just get a new one, no telling how much stress was put on it when the spiders blew.
10-09-2009 12:33 PM
88 jeep yj rearend ???

while flat towing my yj from n.c to tx the rear spider gears exploded. the only thing it damaged was just the spider gears not the ring and pinion[4.88 and less than 3000 miles on them] thank goodness. at the same time the front driveshaft bent badly and i had to remove it in georgia. this i dont understand. the transfer case seems to still work when you shift in to 4wd the front yolk spins on the transfer case. i ordered a driveshaft for the front so hopefully it did not damage the front end. anyway i need to replace my spider gears. the question is this rear has a roll pin securing the center pin instead of a bolt like other rear ends i have been inside. does the carrier have to be removed to tap out the pin ? if so will the carrier come out by just unbolting the main caps [after axles removed of course] and what is the torque on the cap bolts? thanks chris

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 01:50 PM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC