Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > drive shaft U joints completed

Join Wrangler Forum Today


Thread: drive shaft U joints completed Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-13-2009 05:54 PM
porkchop71 I dont. Thats why I take an extra couple days to plan stuff out so I know it goes together after I pull it apart. Although I have taken the mountain bike up to the parts store a few times lol
10-12-2009 01:03 PM
morphious amen brotha u just have to take ur time do the research and go for it word of advise though always make sure u have a back up vehicle just in case
10-12-2009 11:53 AM
porkchop71
drive shaft U joints completed

thanks for the advise on my drive shaft U joints guys. Did em yesterday. Just another project that makes me more confident to dive into the heavier repairs. The right tools, a little time, and a can of PB blaster is key. The one on the diff. side fell apart when I pressed it out and the one on the front was a little harder to get out. But putting em together was a breeze. Word of advise though make sure the caps are all the same size before you install em. On the sage wisdom of another guy on the forum I bought three so it was no big deal. But if you are fixing your daily rig like I was if I didint buy three joints I would have been stuck. Then when I went to return the joint the guy measured the caps and from the factory it had come with one that was a hundred thousands bigger than the other three. I only realized this as it took me three times to take the shaft out and make sure the joint was tight cause it wasnt sitting in the back yoke right. So I switched the one cap around to the other spot and it was not fitting on that side. Im lucky I wasnt trying to press that cap into one of the yokes it just so happened I was lucky enough to have that end in one of the strapped cap locations. So I ripped a cap off the third joint and it fit perfectly. End of story. Topped of the fluid in my transfer case. Then it was time for the test drive. I swear its a totally different truck now. No shaft vibration( there was tons) or nothing. It got rid of a couple noises i was hearing lol. I right this as a testement to the fact that everybody that owns one of these should be spinning wrenches on em. Im about as dumb as a bag of rocks and I am still able to do good solid non Mickey Mouse repairs on my jeep. Next up new front hubs tie rods ball joints and rear axle seals Woo- Hoo. To all you newbies out there dont let the unknown scare you away from finding happiness in taking care of what should be your pride and joy. I have become passionate about doing my own repairs and ask anyone on this forum I bet they are to. Happy Trails.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 06:50 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC