Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > Rokmen Front Bumper Build: Pics

Join Wrangler Forum Today

Thread: Rokmen Front Bumper Build: Pics Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-13-2009 06:18 PM
Originally Posted by mudslinger150 View Post
as you can see im not a perfect welder, but i get good penetration and it's solid...It's all just one pass
Those welds look good ,very nice for a 110v fluxcore! I made my own bumpers years ago out of 2x5 rectangle tubing,1/4 inch wall,yours look exactly like mine,so do the welds,I used the same machine.The only difference is I payed more for the material LOL!
10-13-2009 04:21 PM
G-Pur I need to learn how to f'n weld.
10-13-2009 04:10 PM
Bignuke Could you put a winch on the top of that? and also does the rear bumper/kit come with a swing away tire carrier??
10-13-2009 03:46 PM
mudslinger150 i went to ACE hardware, im sure home depot, lowes etc... would have them too.
10-13-2009 03:28 PM
jwells36 I took mine to two auto parts stores and they did not have anything like that. I wonder if lowes or home depot or maybe tractor supply would have anything like that?

10-13-2009 12:51 PM
mudslinger150 Jwells, what i did was brought my factory bumper bolt to the hardware store, using it i compared the thread pitch and lenght to some other bolts. I wanted to include my smitty built tow hooks so i found some bolts that had the same thread pitch and were about and inch longer than stock, i made sure to get a high grade bolt, so they wouldn't snap under heavy loads.

Ironman, ill have to put a tape up to the rail, ill measure from the ground up to the rail, i'll report back, but its enough to tell with the naked eye.
10-13-2009 12:31 PM
jwells36 where did you get the replacement bolts for the front bumper? I would love to get rid of my torx head bolts up there but have not been able to figure out what size to replace them with. I mean half of the jeep is standard, and half is metric?????

10-13-2009 11:50 AM
Ironman Looks good Mitch. I have winched and pulled full sized vehicles in snow, up hills, over big rock piles, and have never bent a frame rail. I'm not sure how this happened as Jeeps have very strong frames. How much is it off. If it's not too much, I wouldn't worry about it.
10-13-2009 11:15 AM
mudslinger150 the kit was like $109, around $125 shipped. It was fun to build and im thinking about purchasing the rear bumper kit they have, with the 2" reciever.

Has anyone had an issue with the "front Frame rails" (buper is mounted to them) bending? Now that i have this bumper on i noticed that my left frame rail is a little higher than the right one.... is this from getting pulled out by the tow hook, from the bottom of a hill to the top... How would i bend this rail back down? a come along and and anchor point?
10-12-2009 07:28 PM
PT4WDL How much was the kit? Might be easier to put that together than cut and rebuild my bent warn bumper. Also looks a heck of a lot stronger. Hey I wonder if I would be able to reuse the warn winch plate?
10-12-2009 07:02 PM
Originally Posted by mudslinger150 View Post
you said penetration
You said it first!

Nice job on the bumper...looks great!
10-12-2009 12:05 PM
mudslinger150 you said penetration
10-12-2009 11:02 AM
mrcarcrazy Welding looks pretty good. Its all about the penetration!

Good work. looks nice, much better than I could do, that's for sure.
10-12-2009 09:29 AM
mudslinger150 as you can see im not a perfect welder, but i get good penetration and it's solid...It's all just one pass
10-12-2009 09:27 AM
mudslinger150 and finished product, plus i went riding this weekend
10-12-2009 09:25 AM
mudslinger150 more
10-12-2009 09:24 AM
mrcarcrazy I think you forgot something
10-12-2009 09:22 AM
Rokmen Front Bumper Build: Pics

This Friday i was given a Rokmen Front bumper (Kit). I spent Saturday welding, fitting, and painting the bumper. I took a few pics and thought i would share them. If you have any questions feel free to ask, i used a small lincoln 110 with flux core, turned high heat, low speed

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 08:01 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC