Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > WF Local > WF Local Forums for Your Region and State > Oregon Jeep Forum > Transfer case drop. motor mount lift?...

Join Wrangler Forum Today


Thread: Transfer case drop. motor mount lift?... Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-17-2013 04:49 PM
lonewolf422 Just like the other guys above, ditch the body lift, get an SYE and new rear drive shaft. If your ballin on a budget, you can get a driveline shop to build you one out of the front drive shaft of a TJ.

Good luck!
09-17-2013 10:38 AM
IslandTJ I'm not sure how tall your tires are but with your 2" Skyjacker and 2" body lift, I am guessing you have either have 33" or 35" tires...

Best scenario is for you to junk the existing setup and start from scratch but if that's not feasible, then for 33's, you may get by and resolve your shifter hitting the console by replacing the 2" body lift with a 1" and removing your transfer case drop. If you have vibes from removing the drop (rare for a short 2" lift), you can lower the skid, one washer at a time, to dial out the vibes.

If you have 35's, start from scratch or sell them for 33's.
09-16-2013 11:40 PM
Teague242
Quote:
Originally Posted by jaytheminor View Post
so if i ditch the t-case drop for a mml thats not gonna work huh? i was told it would.
Well he is addressing the problem of the shifter.... The body lift is the problem there. 1.25 body lifts coupled with a 1" MML is known to cause problems shifting. And you got a whole 2 inch body lift on there lol.

The motor mount life MAY help with your issue of the transfer case drop. You might be able to trade the 2" spacers for 1" spacers... Maybe even be lucky enough to not require spacers at all... But I doubt that will happen.

Just ditch the body lift....
09-16-2013 11:24 PM
jaytheminor so if i ditch the t-case drop for a mml thats not gonna work huh? i was told it would.
09-16-2013 10:55 PM
IslandTJ
Quote:
Originally Posted by IslandTJ View Post
The 2" body lift and drop is your issue. Many resolve by by trimming the plastic and/or body where it won't clear on the shifter, while some will heat and bend the shifter itself.

Not a fan of body lifts exceeding 1", perhaps consider abandoning that tall of a body lift.
09-16-2013 10:48 PM
chevymad When I did my body lift and mml it moved my shifter back so that it hit the console in 2 & 4. At first I took the screws out of the console moved it back a 1/2" and drilled them back in again. Later on I bought a B&M shifter. The shorter shifts mean that the stick doesnt move as far back. After installing the shifter I moved the console back to the original position and everything works great.
09-16-2013 09:45 PM
banks316 Motor mount lift will make your problem worse. The reason for the Tcase drop is for your drive line angles so the rear slip works as its suppose to. Increasing the engine highth will cause your trans and case to pivot. This will change your drive line angles. The change could be minor or major that depends on your current angles. This could cause added vibration from either of the driveline or both. You got two options. 1) Eliminate the tcase drop, this might mean SYE/DS that depends on your current set up. 2) Eliminate the body lift.
09-16-2013 08:12 PM
Teague242
Quote:
Originally Posted by jaytheminor View Post
well im thinking about going with a motor mount lift. I'm convinced that with this i could ditch the t-case drop and everything would be okay. Or at least this says so.

Motor Mount Lift for a Jeep Wrangler
Try it. If it doesn't completely eliminate the need for the Tcase drop spacers, then you will be able to at least be able to use thinner spacers.
09-16-2013 07:49 PM
jaytheminor well im thinking about going with a motor mount lift. I'm convinced that with this i could ditch the t-case drop and everything would be okay. Or at least this says so.

Motor Mount Lift for a Jeep Wrangler
09-16-2013 07:09 PM
Teague242
Quote:
Originally Posted by jaytheminor View Post
its got a two inch skyjacker suspension lift and two inch body spacers. also a two inch transfer case drop.
Well the body lift is a bit too much. It would be expected for the shifter to drop like that. The transfer case drop doesn't help either.

Either get rid of the body lift, or get an SYE... My vote goes to the body lift.
09-16-2013 03:42 PM
FireMike I had this same issue. I removed the dust cover and then removed the foam protector from around the shifter its self. I have 98 so I don't know if this will apply to your 04. But it cured the problem for me! Hope you get it fixed!

But the best ( and expensive in relation) solution would be to get a SYE/DS for the T-case. That is what I will be doing shortly.
09-16-2013 02:41 PM
jaytheminor its got a two inch skyjacker suspension lift and two inch body spacers. also a two inch transfer case drop.
09-16-2013 02:36 PM
Teague242
Quote:
Originally Posted by jaytheminor View Post
I have a body and suspension lift on my 04' tj wrangler and of course i had to have a transfer case drop. Due to the transfer case drop my shifter angle is off and it hits the console and my shift boot won't fit anymore. This drives me crazy! i was told if i got a motor mount lift kit and got rid of the t-case drop this would solve the problem... is that right? please help!
It might help by telling us how much lift is on the jeep. I'm assuming somewhere around 3"? And how thick is the washer/spacers between the frame and the skid plate?

I know that it's possible for an MML to improve driveshaft angles and help with vibrations, but never had any experience with it myself. Maybe someone else can help with that.
09-16-2013 02:33 PM
jaytheminor
Transfer case drop. motor mount lift?...

I have a body and suspension lift on my 04' tj wrangler and of course i had to have a transfer case drop. Due to the transfer case drop my shifter angle is off and it hits the console and my shift boot won't fit anymore. This drives me crazy! i was told if i got a motor mount lift kit and got rid of the t-case drop this would solve the problem... is that right? please help!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:01 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC