Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > transfer case bolts

Join Wrangler Forum Today


Thread: transfer case bolts Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-30-2009 04:00 PM
jeepers92 Congrats, they can be a pain in a$$
12-30-2009 03:57 PM
bwilburn Well I tried every method you guys gave me had very good success. I removed all six with none broken or stripped. I did have 1 stubborn one, Talked to a old timer He gave me some advice I tried and I thought I would share it. He suggested to spray with pb blast and then heat with a propane torch, Repeat until you suceed. It took me a couple times. I tried it one time at night no sucess sprayed it went to bed and in the morning did it again a couple times and bolt came out. Very slow going but better than a broken bolt or striped nut.
12-23-2009 02:12 PM
morphious remember though take ur time and soak em good i already started mine and i dont plan o doing it for a month I'm not screwing around though i want it done in a day
12-23-2009 01:14 PM
bwilburn Well sounds like pb blast is the way to go. Gonna give it a try. Thanks for advice
12-21-2009 06:12 PM
cheapjeep71 It sucks when you break the welds on the nut inside the frame. Trust me, I know. PB Blast the hell out of it. I'd spray them for at least a week, then spray them for another week after that.
12-21-2009 02:49 PM
NAVYCHIEF also, after the pb blaster, try tightening them a little then loosen them.
12-21-2009 02:10 PM
1992wranglersahara PB Blaster. Spray it on liberally and hammer the bolts lightly to encourage it to get down in there. Keep doing that over and over for a day or two and then give it a go. They can be really tough to get out, so be prepared.
12-21-2009 12:43 PM
morphious all else fails use the torch to heat um up
12-21-2009 12:11 PM
jeepers92 Try using pb blaster it is better than wd forty, and give it time to work!
12-21-2009 11:43 AM
bwilburn
transfer case bolts

Does anyone have a good way to remove transfer case cross member bolts, with out breaking them. I tried air impact, a breaker bar with pipe, no luck.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:38 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC