Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > HVAC LED light install question

Join Wrangler Forum Today

Thread: HVAC LED light install question Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-02-2010 07:21 PM
BLACKTOOTHGRIN Can't recall the specific part #'s either.
Do as TWOZEROFD suggested,
and read through the INTERIOR LIGHTING thread that we put together.
If I remember correctly, everything you need to know is in that thread in detail....both for the older model TJ's like mine, and the newer ones like his.

BTW TWOZEROFD... are your LEDs still holding up?
So far so good for mine...but I don't do a HELL of alot of night driving.
01-02-2010 06:05 PM
abw0004 What was the size and type of bulb used for the PRND21?
01-01-2010 06:40 PM
Twozerofd if you read the whole thread it says what bulbs fit where, i forget what size i used. i think the switch led's were smaller than the hvac led's
01-01-2010 04:58 PM
abw0004 Actually for the switches for the defroster and such, did they require the same bulbs that the hvac used?
01-01-2010 04:55 PM
abw0004 this helps a lot. thanks!
01-01-2010 04:39 PM
Twozerofd Nevermind i found my write up. search for the thread "Interior Lighting" started by blacktoothgrin. go to page 3 of the thread, about 3/4 of the way down is my write up. hope it helps!
01-01-2010 04:31 PM
Twozerofd give me your email. i did an entire write up on the HVAC dissasembly.
01-01-2010 04:31 PM
kdukes4 there should be two plugs that look somewhat similar to the ones that you pulled in your cluster, one on each side of the hvac unit. those are the bulbs. just have to turn it 1/4 of a turn and it should come loose to pull out. i tried putting my leds in there and they kept blowing on me... i just put the old ones back in.
01-01-2010 04:10 PM
abw0004 Do I need to disconnect it from the harness? And does it come out from the back like the gauges did or do I open it up?
01-01-2010 04:05 PM
ilovegeeksnj 1st take the middle trim piece that goes around radio and hvac. then remove the hvac screws pull it out a bit and there are 1 bulb on each side they look the same as cluster. its very easy
01-01-2010 01:25 AM
HVAC LED light install question

I am replacing the hvac bulbs with blue LED's and I am confused on how to get the original bulbs out and these in. I already replaced the gauge lights and I know how to get the housing for the hvac controls off. Pictures and directions would be greatly appreciated! Thanks!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 09:10 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC