|11-21-2014 11:53 AM|
|Jerry Bransford||Any ATF+4 is fine since it has to meet the specs as defined/required by Mopar to be called ATF+4.|
|11-21-2014 11:50 AM|
|WranglerAngel05||Wal-Mart or Advance it is... Lol|
|11-21-2014 11:48 AM|
|11-21-2014 11:35 AM|
|WranglerAngel05||Via the original poster's question, I have also found most people to say that ATF-4 is best for the transfer case (at least regarding the NV241). I have seen a few threads where people have used Royal Purple Syncromax in the Transfer Case. Any real benefit in that or is it just wasted money? I apologize in advanced if it's a questioned asked 18 million times, but I've been all over the forums the last two days and can't seem to find a conclusive answer. Thanks!|
|10-20-2014 01:53 AM|
|SilverTJMike||TJ 05/06 Manual tranny 6 speed takes Mopar fluid don't remember the part, ran that for a bit, switched to Pennsoil Synchromesh then last time I switched to AMSOIL Synthetic Manual Synchromesh Transmission which I seem to be happier with. Shifts a bit better in the cold. Specifically it takes a synchromesh, not a regular oil.|
|10-19-2014 08:37 PM|
|10-19-2014 08:09 PM|
|Jerry Bransford||Any mods to the Jeep like a suspension lift or transfer case drop? Mods can change how much ATF the tcase can hold. Regardless of mods or no mods, the ATF level is fine if the tcase is filled to the point it overflows the fill hole.|
|10-19-2014 07:55 PM|
So to bring this dead thread back but didn't want to start a new one if its already out there.
I did my transfer case the other day it took about 1.25-1.5 quarts of ATF, I stopped when it started pouring out the fill hole. I then put the plug in waited a while and removed it to check that it wasn't just filling to fast and it poured out.
My question is how come the service manual says it takes 2.0L?
thanks and sorry again.
|01-12-2010 12:14 PM|
|Schmo||What about the 6 Speed Manual Tranny (NSG370) . . . what type of oil does it take? All the information I've found is for the older manuals and they seem to call for Mopar Manual Trans Lube . . . would the 6 speed take the same? Anybody know how much the 6 speed takes too?|
|01-12-2010 02:52 AM|
|01-12-2010 12:51 AM|
231's TC's in any vehicle aren't picky about the ATF you put in it. Any name brand ATF+4 will work just fine.
|01-11-2010 07:25 PM|
|01-11-2010 07:21 PM|
|Hensman||Ok, thanks guys.|
|01-11-2010 02:29 AM|
Your 6 speed is a NSG370...
Click link for trans specs...
|01-11-2010 02:27 AM|
I'm in the same boat and have been doing some research! The FSM says that the NV231 and the NV241 both take ATF + 4 . . . the NV231 only takes 1.0 L (2.2 pts) the NV241 takes 2.0 L (4.2 pts)
Quick Question . . . I have a 2006 Rubi Manual 6 Speed Tranny and 4:1 TC . . . Which TC do I have NV231 or NV241 . . . and which Tranny do I have? The FSM I have is from 2004 so it shows the NV1500 and NV3550, but I don't think they had the 6 speed in 2004 so I'm not sure if mine needs something different. Thanks!
|01-11-2010 01:56 AM|
1.2 liters...2.5 pints.
I use Mobil 1 ATF.
|01-10-2010 11:44 PM|
Transfer case fluid change
I have a 2005 unlimited with 61,000 on the clock. I think its time to change out the fluid and was wondering how much fluid it takes and also if ATF-3 or ATF-4 is better. Thanks for the help!