Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > bleeding the clutch on my 89

Join Wrangler Forum Today


Thread: bleeding the clutch on my 89 Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-15-2010 04:31 PM
jr. hopefully i can get it working better this weekend thanks guys
01-14-2010 06:10 PM
89PBR96 Be careful JR when you try and break the allen head screw loose on that because you might strip the plastic threads in the master cylinder I had to replace mine when I installed the new clutch
01-14-2010 05:36 PM
scott howard The bleeder is on the drivers side coming out of the bell housing.
A power bleeder like a mighty vac bleeder is the best way to make sure all the air is out.
and make sure you first remove all the old fluid since you do not know what kind of fluid they used ( dot 3 dot 4 ect. ) so remove the old stuff and just refill with dot 3 brake fluid .
01-14-2010 04:25 PM
jr. i've looked all over can't see any leaks,and also i don't see the bleeder anywhere.the master cyl.is down on min.it seems to get worse as the engine gets hotter.the po said the motor and tranny are remans with about 40,000 on them and that they replaced the clutch then. thanks guys i'll try some fresh fluid
01-13-2010 10:33 PM
scott howard Flush the brake system and start with all new ( brake 3 fluid ) .
This will let you start with new fluid and no air in system to see if your clutch works.
If pressure will not come back then it will be time to replace some parts and the next easiest part is the clutch master cyl. and if that does not work it is time for a new internal
slave cyl . and instead of doing that go ahead and replace the whole clutch and flywheel including changing it over to a external slave cyl. so it will be easy if you have to do it again years done the road.
01-13-2010 08:49 PM
cheapjeep71 Hopefully it's not the slave. It is inside the tranny.(What a pain !!!). MIne did the same thing a few years ago. I went ahead and switched out the master. It seemed to do better after that.
01-13-2010 06:44 PM
copleydad It takes brake fluid.

When did this start? Any leaks on the driveway? On the firewall behind the Clutch Master? Any leaks up under the dash above the accelerator? You say it's not empty so I am guessing it's not full????

Bunch of scenarios here. Could be a small leak in a line, could be a corroded bleeder valve coming out of your slave, could be it just sucked up a bit of air if it's "not empty" but not full. Start with the simple first, check for some brake fluid leaks
01-13-2010 06:28 PM
jr.
bleeding the clutch on my 89

should i replace the master cyl. first it's not empty but my clutch goes to the floor before it disengages and also does it take a special fluid(i've never had a hyd. clutch before )

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:55 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC