Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > 2.5L Blown Head Gasket

Join Wrangler Forum Today


Thread: 2.5L Blown Head Gasket Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-03-2010 06:21 PM
punchy It's not too hard of a job to do. Before you start tearing things apart, go to your preferred parts dealer and get a head gasket set. You'll probably have to order it, but it's worth it. It'll have all of the gaskets you need plus quite a few that you won't need... and it's cheaper than buying everything individually. It also has new valve stem seals.
After you get the head off, take it to a machine shop. They can shave it down if it's warped, check it for cracks, make sure your valves are seated properly and put in your valve stem seals. Plus it will be all nice and clean when they're done. I had my 2.5's head worked about 2 weeks ago for around 85 bucks. I had it back in two days.
Get everything you need for an oil change and a couple of gallons of antifreeze and your set.
x2 on the chilton's or haynes manual. There's a sequence to torque down your head bolts.
Also, when your refilling your radiator, remove the heater hose thats next to the thermostat housing. It helps eliminate that horrible air bubble in your system. When antifreeze starts to come out of the opening at the thermostat housing, put the heater hose back on and burp your radiator.
I'm sure I've forgotten something....
02-03-2010 04:52 PM
Eagleridge5 Get a Chiltons, Clymers or Haynes manual and have fun. Mark everything you disconnect with a tape numbering system so you hook all the doodads back up to the right place. Take some digital photos as you dismantle stuff. The head gasket is probably the easy part. Pay attention to the torque and tightening sequence!!
02-03-2010 04:42 PM
Garyk Get yourself a Haynes or Chilton repair manual and have at it. Do it sooner than later, that chocolate shake is not doing your bearings, cams, lifters etc any good. Changing the head gasket is not all that hard, takes longer to get all the crap off the that's in the way than the actual head removal.
02-03-2010 01:57 PM
Silver The problem problably is in a blown head gasket.
Need to replace that. That chocklate shake isn't good for the engine.
I think it isn't hard to change it, but I rather give this job to a experienced car dealer.
01-31-2010 11:49 AM
johns37363
2.5L Blown Head Gasket

Im a newbie here, so thanks in advance for any advice and information. I am about to replace the head gasket on my new toy, any advice from a vet is greatly appreciated!! Still runs(pretty good actually) but I have the choclate shake in the crankcase. Coolant is clear....but I have to add it frequently.
Thanks!
Steve

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:27 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC