Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Quick clutch question

Join Wrangler Forum Today


Thread: Quick clutch question Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-17-2013 09:51 PM
W5KVV Sounds like the new master/slave isn't pushing the throwout bearing arm far enough.

Were you having these symptoms before the new master & slave?

As far as my problem goes, I'm just going to pull the tranny on it. It's started growling now on start up, RPM & vehicle speed have no effect on it, nor does the position of the clutch or. Does it any time the engine is running regardless if it's in neutral or a gear. It's not motor noise. It's definitely coming from the bell housing. Leading me to think the pilot bearing is about to crap the bed. I'm just gonna rebuild everything. Clutch, flywheel, master/slave, throw out bearing, pilot bearing, everything. I want to be done with it.




There goes my money for new tires.
10-17-2013 08:36 PM
tembko Matt I hope you don't mind me jumping onto your thread but I have a similar issue and I'd like your guys' input. I have an 88 JY with a NP435 transmission and an external slave cylinder. I just replaced the master clutch cylinder, slave cylinder and now the jeep will only go into gear periodically. It grinds horribly trying to go into 1st and reverse. 2nd, 3rd and 4th go in harder than they did with the old slave and master. Sometimes, it wont go into any gear. I've bled the air out...is there an adjustment I'm missing somewhere or is there a bigger problem?
10-16-2013 10:29 PM
W5KVV Master & slave are clean as a whistle & full of fluid. I guess the next step is to pull the slave & do the screwdriver trick.

I'm getting a good ol fashion feeling it might be internal.
10-16-2013 10:14 AM
W5KVV Damn Chris I think you hit the nail right on the head. Reading your post it just clicked. I have been hearing the throw out bearing growling since I got the Jeep. I keep telling myself it's gonna need replaced one of these days.

Why I didn't put 2 & 2 together is beyond me. I'll check the fluid level & check for leaks, but I bet the T/O is ready for retirement. It's been raining cats & dogs here the last couple of days & my shop is full with another project. Needless to say I'm ready for it to dry out around here.
10-16-2013 10:00 AM
sevenservices first things first, pump your pedal 10 times with it running, shut it off then check your clutch fluid on the firewall. My wifes old nova had a clutch leak and it would do that same thing. Every week or so we'd have to add some fluid because it would not want to come out of any forward gear. It could have air in the fluid as well, its just not pushing the pressure plate far enough away from the flywheel.

Secondly, if your fluid is full and slave cylinder is good, then it may be time for a new throw out bearing.
10-15-2013 11:12 PM
W5KVV Thanks for the reply jokerchief. I just wanted a 2nd opinion. It never hurts to double check yourself.
10-15-2013 10:32 PM
jokerchief462 Yes it is probably time try Rockauto for the combo ore led setup. 30 minutes your on the road.
10-15-2013 08:08 PM
W5KVV
Quick clutch question

Guys, I think I remember this from my older Jeep days, but I better ask before I throw money at it.

The tranny on my 95 YJ is hard going into & out of any forward gear from a stop. Goes into reverse fine with minimal grinding if it's already in neutral.

Here's a scenario: I pull onto an incline in first, bring the Jeep to a stop, kill it & release the clutch. Start the Jeep back up, push the clutch all the way to the floor & the shifter doesn't want to come out of first & the Jeep won't roll. (not a big incline, but big enough the Jeep should free roll). If I rock it, it comes right out of gear & everything is golden.

Pretty sure it's hydraulic... right? Either low on magic clutch juice, or a bad master/slave. It's factory equipment, so I'm sure it's about due.

For the record, the syncros are good. I can bang thru the gears as fast as I want & have no grinding what so ever. Up shift, down shift no grinding at all.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:13 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC