Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Need help with my kc lights.

Join Wrangler Forum Today


Thread: Need help with my kc lights. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-18-2013 03:33 AM
Shawnbn We just bought it and the lights aren't wired in yet. That's my next job. And I like the orange jeep. It matches the color of the jeep. Lol
10-18-2013 02:53 AM
jackor No, you can't tell from that picture. A real "fog" will have a piece of metal wrapped over the bulb right behind your "ee" i jeep. Another way to tell is to turn them on and take another picture. A real fog will be completely lit up in the bottom half, and almost no brightness in the 4 grill squares above you "ee"

...or turn them on at night against a wall and check the beam for yourself. a fog will make a bright horizontal bar of light, some light scattering below that bar, not much light above that bar. a flood will put out a large soft area of light like a house lamp, and driver/euro will have a very obvious hot spot in the center. From the lens, it can only be one of these 4 types( it's not a spot like someone else said). The only reason you would want to know is of course, if it's a real fog, you definitely don't want it up there. so when are you going to black out that orange writing on the lights? That's bright enough without turning them on. LOL
10-17-2013 08:14 PM
reno92 The two center lights look like spots and would be fine. I can't tell if the two outside lights are fog or driving. Driving won't be as bad a fogs up there, but spot or pencil is what you want. A spot or pencil will normally have a clear lens, no grooves in the glass. Fog and driving will have grooved lens.
10-17-2013 08:03 PM
Shawnbn From the pics I uploaded can you tell what type they are?
10-17-2013 02:24 PM
reno92
Quote:
Originally Posted by jackor View Post
What's more strange to me is that it came with 4 installed lights with no wiring installed.

My advice would also be to take the 2 fogs off the roof and get them down on the front bumper then buy another set of spots, drivers or even euro beams to put up there. Fog's don't belong up that high up with their wide and narrow beam, you basically need to point them nearly straight down at the ground to see them light up anything useful. ...that is if they're real fog reflectors with the shield over the bulb.
I agree, fog's have a wide and downward pattern meant to light up the road right in front of you. Having them on the roof will cause a lot of light to fall on the hood causing a lot of glare off the hood. Stick with pencil/spot beam up top and mover the others to the bumper
10-17-2013 02:14 PM
Shawnbn Thanks all for the info. I believe they are driving lights. And for the wiring yes I will be using a relay. And I planned on switching out the torx for hex
10-17-2013 01:16 PM
jackor What's more strange to me is that it came with 4 installed lights with no wiring installed.

My advice would also be to take the 2 fogs off the roof and get them down on the front bumper then buy another set of spots, drivers or even euro beams to put up there. Fog's don't belong up that high up with their wide and narrow beam, you basically need to point them nearly straight down at the ground to see them light up anything useful. ...that is if they're real fog reflectors with the shield over the bulb.
10-17-2013 01:05 PM
W5KVV Black is always ground on a 12 volt system.
10-17-2013 12:57 PM
Tom95YJ Black is always ground White/Red are always Hot !

10-17-2013 11:31 AM
JWBooth Shawnbn, Welcome to the club. Lights will be just the beginning.

Use black as the ground, same at the battery terminals/leads. Are you wiring in a relay with that many lights?
10-17-2013 11:11 AM
Hip To Be Square
Quote:
Originally Posted by Shawnbn View Post
Also what size torxs is the seat belt holder? I have to replace the back seat seat belts so the baby's safe. Thanks for all the support.
It is a T50 Torx bit. If you don't already have a good Torx socket set in your toolbox, now is a great time to invest in one. Every time I unbolt something on my jeep that was held on by Torx bolts, I try to replace it with a Grade 8 hex bolt so it is easier to remove later.

Good luck on the new jeep!


On a side note, for what it's worth, I too would wire the white as hot and the black as ground- just for uniformity's sake.
10-17-2013 10:17 AM
AllMudd
Quote:
Originally Posted by Decoy_58 View Post
I would wire black hot white ground or if you have a multi meter you can check to see which one is ground
This is some what funny. I would do black ground and white positive. Since the negative/ground on your battery is already black. This way you don't get confused later on what one is hot. Black to me is always ground and colors blue, red, yellow, white can be a voltage sources. Just my .02.
10-17-2013 09:18 AM
Shawnbn Also what size torxs is the seat belt holder? I have to replace the back seat seat belts so the baby's safe. Thanks for all the support.
10-17-2013 08:48 AM
Shawnbn Okay and when I wire the lights in and run them through the tube, what would be the best area to run them into the cab. Through the window frame or through the body under the window frame.
10-17-2013 08:31 AM
Decoy_58 I would wire black hot white ground or if you have a multi meter you can check to see which one is ground
10-17-2013 08:11 AM
Shawnbn
Need help with my kc lights.

My girlfriend and I just bought a 91 wrangler and it came with 4 kc lights on a overhead light bar. Two are floods and two are spots. The wiring is black and white. Which one is hot? I think it's the white but just want to make sure before I wire them wrong. Thanks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:33 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC