|10-20-2013 12:27 PM|
Fill out your sig so we know what your working with.
If you have a manual transmission, there could be a problem engaging 2nd 4th and reverse gears because of the angle the transfer case drop kit creates. If you experience this, you need to pull the rubber boot off your shifter and cut the metal on the back of the shifter hole.
If you have a manual tranny, sit in your jeep and look at the shifter. The rubber boot at the bottom of the shifter? That comes off and there is a hole there. The side of that hole closest to the back of the jeep is where you will need to trim...
Or you could just drive around in 1st 3rd and 5th and push it backwards...lol
|10-20-2013 12:13 PM|
|harleydragon||I don't have a pic..if you take the shifter boot off you will see a rectangular hole in the jeeps tub that the shifter fits through..a small section of the tubs sheetmetal in between the rectangular hole and the screw holes where the boot attaches may need to be removed..I would try it first because this may not be necessary|
|10-20-2013 11:50 AM|
|10-19-2013 08:44 AM|
|coolin4u||My plan is a few weeks is to install a 1'' MML and remove my transfer case drop,i only have 3'' of suspension lift and 1'' body and have no issues right now just don't like the clearance loss with the drop.I'm hoping the MML works out ok.|
|10-19-2013 08:14 AM|
|simonclay||When I did my TC drop I couldn't shift into 2nd, 4th or R. So I trimmed a little bit of metal like Harley says. But then the lower rubber boot that the shifter goes through was binding and not really letting me go into 2nd or R. So I need to move my shift boots back about 3\4 inch. Just so you know|
|10-19-2013 07:36 AM|
|10-18-2013 07:19 PM|
|10-18-2013 06:57 PM|
|Square_Eyes||They don't come stock with CV shafts or slip shafts, stock yjs have a slip yoke on the transfer case that allows it to change length, if you are running a slip yoke eliminator kit then you will need the drive shaft to have a slip joint (one that moves in and out, changing the length of the shaft). A CV drive shaft is also known as a double Caradan joint or constant velocity (CV) meaning it has one end that has two u-joints increasing the range of motion the drive shaft can move before binding and breaking parts.|
|10-18-2013 06:51 PM|
|10-18-2013 06:20 PM|
|Moneymaker4567||No my stock CV drive shaft is not long enough. But I'm saying for a transfer case drop kit how can I avoid or fix the stick messing up ?|
|10-18-2013 05:30 PM|
|harleydragon||the driveshaft has to be able to change lengths as the axle moves up and down..this can be done with the stock slip yoke that moves in and out of the transfer case or with a driveshaft with a slip yoke in the middle but you must have one or the other..if you don't you will bust the transfer case|
|10-18-2013 05:18 PM|
|Moneymaker4567||I'm saying I don't have enough money for a CV rear drop kit. And that's what I'm afraid of my gears being messed up !!|
|10-18-2013 03:12 PM|
|YJ fanatic||How are you running a SYE without a CV shaft? Do you have a normal shaft with a slip in it? Because its not possible to run an SYE with the stock shaft.|
|10-18-2013 02:45 PM|
The only thing I've seen is that with a 4" lift and no drop kit, its good your running an SYE. If not, you'd trash u-joints weekly.
Aside from that, I still have not adjusted my shift linkage on the column (auto). It rides a little under where its supposed to. Basically, N is Drive and Drive is 2 and 2 is 1 and 1 is at the bottom. Also, when its up in Park the shifter bumps up against the dash.
Its prob. just a linkage I need to adjust but haven't felt like dealing with yet lol.
|10-18-2013 01:54 PM|
|jokerchief462||Thats it a clearance issue nothing else.|
|10-18-2013 01:31 PM|
disavantages of having a transfer case drop kit on a yj
So I have my Yj lifted to about 4 inches ( I say about because I have shackles and suspension lift kits) and I have a slip yoke eliminator but no CV rear drive shaft and no 300$ right now. But I was wondering what are the disadvantages of a transfer case drop kit on a yj (besides the fact it lowers your clearance) thanks