Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > So who makes good exterior door handles?

Join Wrangler Forum Today


Thread: So who makes good exterior door handles? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-28-2010 02:39 AM
s3nt3nc3d
Quote:
Originally Posted by distortedtj View Post
For the handle itself I personally like the oem handle. Crown eprs. makes replacement parts "replicas". I'm cheap too...I'd end up getting a use one from a junkyard or Daveysjeeps.com.
Submitted a request for the parts are daveysjeeps.com

Thanks for the info!

OEM door handles sure ain't cheap... i'll have to see what kind of employee pricing I'll get at the dealership, but the site I just checked which is usually close to our prices says $100 per door handle. OUUUUCH.
02-28-2010 12:42 AM
distortedtj For the handle itself I personally like the oem handle. Crown eprs. makes replacement parts "replicas". I'm cheap too...I'd end up getting a use one from a junkyard or Daveysjeeps.com.
02-28-2010 12:39 AM
s3nt3nc3d
Quote:
Originally Posted by distortedtj View Post
CROWN enterprises....if you have a Quadratrac catilog look in there.
I've seen em listed on some searches...so they're good? Seem to be inexpensive too...hell, less expensive that the ones I bought even.
02-28-2010 12:17 AM
distortedtj CROWN enterprises....if you have a Quadratrac catilog look in there.
02-28-2010 12:10 AM
s3nt3nc3d
So who makes good exterior door handles?

For full steel doors.

I installed mine tonight...they're the black ones from "Omix-Ada" and they freaking blow. The passenger side one works good...for now. But the driver's side one...I got it installed. Tested and worked. Dabbed some paint on the scrapes from where I apparently dropped/slid it on the concrete

5 minutes later I go to open the door and "POP!"

The damn catch on the handle that pushes the lever the latch rod is attached to popped OVERTOP that lever due to the amount of play in the rivet holding that lever to the handle. So...I had to tear the entire door back apart...

Pulled it out... bent the lever a little bit so even at it's maximum distance, it would still catch.

Reinstalled it...reassembled my door. Tested it about 150 times (no joke). Cleaned up my mess... worked on a few side projects.

Go to get in my Jeep to head home...exhausted. POP!

You guessed it...it popped out of place again.

Disassemble door. For the 3rd time.

Remove handle...bend lever again. Cheap metal begins to crack.

So I am faced with a choice...reassemble the door with the old chrome handle (and have the Jeep look goofy) and attempt to contact 4wd.com to exchange it for a piece of crap replacement or risk modifying it and breaking both handles...leaving me with a hole in the door until I get a replacement ordered next paycheck.

I decided to modify it... so I drilled out the rivet. Popped the components off... took my old handle and drilled out the rivet on it as well. Shortened a bolt that would fit through the hole enough that it didn't hit the handle, put a nut and a lockwasher on it and tightened the assembly down so the lever could move without too much effort but there was very little play in it for it to slip.

Reassembled the door for the third time... go to crank the window up.



When I'd put the window back in the 3rd time, I had one side out of the channel....disassemble door for the 4th time...adjust window back on track. Reassemble.

So now my handle is working...at least until my rig job loosens up...and it looks like crap (well not THAT bad...but sure don't look nice and new anymore). Ugh...on the bright side...I took pics of the steps to do the door handles so I can post up a how-to with photos for those interested.

First door took me about 2 hours to figure it all out...I think I got it down to about 10 minutes now. lol

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:17 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC