|05-02-2010 08:01 PM|
I like it blacked out but my Jeep is black so I took them off, reminds me of the TJ with the Jeep logo off, I am a little sad they didnt keep it on the side like they did for many many years
|05-02-2010 12:38 AM|
|InfernoGirl||x2 on this^^^^ If you don't scuff them it will wear off pretty quickly, and scuffing them without removing them would be quite a challenge. Taking them off is easy as pie, like Mr. Goon said, cutting the tape to re-adhere them is probably the hardest part of the job.... To me the looks make it worth the effort. If I had a JK, I'd definitely do it. In fact, if you don't want to do the trimming, etc, take off the letters, send 'em to me, and I'll send 'em back to you ready to stick on... for a small fee|
|05-01-2010 10:25 PM|
|05-01-2010 10:13 PM|
......resurrecting the thread with a quick question.........
Think black touch-up paint would work w/out taking off the lettering?? I already have a bottle from a previous vehicle I owned.
|04-25-2010 11:37 AM|
As far as the weight is concerned I had some sagging and this was resolved once I got a lift.. I have a 3.21 gear manual transmission and never experienced an issue with that extra weight..(I also have the RR rear bumper, front skid plate and their tubular side armor)
|04-25-2010 11:35 AM|
Looks like the Rugged Ridge XHD bumper....
Rugged Ridge Modular Heavy Duty Bumpers - Quadratec
|04-25-2010 10:32 AM|
|chalex807||I like that bumper, which one is that and was it hard to install? Would the extra weight of a steel bumper be a bit much for my stock geared manual tranny jeep?|
|04-25-2010 08:54 AM|
|04-25-2010 01:16 AM|
|blaster199||B/c the letters are chrome did you sand the actual letters before hitting them with the spray paint? I would think a light sand would be necessary for the paint to stick properly|
|04-14-2010 09:17 PM|
|J.B.||@Antigoon...They were kindofa pain I thought also! But like the directions say... another set of hands woulda helped bunches...glad ya gottem in place Bud!|
|04-14-2010 06:54 PM|
|04-13-2010 06:22 PM|
|InfernoGirl||Fusion for plastic would be best, since they're plastic.... Not necessary, but if you're buying anyway.... Put some clear over them to protect them from chipping, too.|
|04-13-2010 05:17 PM|
|wrangler0||What's the best kind of spray paint to use??|
|04-13-2010 04:56 PM|
|DakotaBuck||Looks great, also adding this to my to-do list - Thanks|
|04-13-2010 07:28 AM|
Indeed they haven't been done yet.. For one or another reason I had an issue removing the side marker base..Still got the guards and now you have put me on notice...
|04-13-2010 07:13 AM|
You can get wax & grease remover specifically for this purpose. $5 at O'Reilleys
Wipe it on wet, dry it off.
Also, when you strip the emblem off, you need to remove all of the adhesive from both the vehicle and the emblem. It can be a painstaking process but because your vehicle is fairly new, it may not be too much of a challenge. There are a number of products that will do this. I prefer good old fashioned lighter fluid. It's cheap and it won't harm paint or plastic. Remove as much of the foam as you can then wet it with the fluid it and work the adhesive off.
Use the right tape to put it back on. Household stuff isn't tough enough to hold up the the elements.
3M 3609 - Scotch-Mount™ Molding Tape, 1/2 inch x 60 inch 3M-3609 3M3609 3M 3609
Apply the tape to the back of the emblem and then use an Xacto knife or razor blade to gently trim around the edges so that it won't show when you reapply the emblem to the vehicle.
|04-13-2010 07:07 AM|
|WranglerX2009||Looks decent. I just left mine off all together. I like it that way personally.|
|04-13-2010 06:54 AM|
|J.B.||Hey Antigoon...looks like ya missed your side marker guards? I went with the light guards on my rig all around too. Like the way they look! Your Rig looks Awesome Buddy!|
|04-13-2010 04:37 AM|
|04-13-2010 04:32 AM|
|04-12-2010 11:28 PM|
|04-12-2010 11:15 PM|
Is that Rescue Green or Natural Green Pearl??
|04-12-2010 09:54 PM|
Do it the right way and these letters will not come loose and last but not least, it looks professional..
|04-12-2010 09:46 PM|
That is a little more work that I was hoping for, but the results look to be well worth it. I will have to think long and hard about this one.
Thanks for the info.
|04-12-2010 09:30 PM|
But no pain, no gain...
|04-12-2010 09:14 PM|
|blaster199||That looks saaweet! I considered that but didnt think it would re-stick...this has now been added to my next mods!!|
|04-12-2010 09:07 PM|
Yes, I did it and it looks nice.. You need to take them off with a piece of fishing line. Like sawing through the letter foam backing with this line.. The imprints on the grille give you a good mark as to where to re-install them.. Sand them down with some soft scrub pads, solvent clean and spray paint them..
Then re-apply some 3M outdoor molding 2 sided tape (is a painstaking job to cut the letter contours) Clean the grille surface with some solvent and stick the letters back ...Keep some push pressure on the letters for about 2 minutes..
|04-12-2010 08:55 PM|
Black "JEEP" letters on grill
Has anyone done this? It is the only chrome on my Rubi and I don't like it. What would be the best way to black these out?