Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Moisture behind Bushwacker guards?

Join Wrangler Forum Today


Thread: Moisture behind Bushwacker guards? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-14-2010 03:01 PM
adawg38
Quote:
Originally Posted by adawg38 View Post
The steel or aluminum would definately be alot stronger and take more of a hit but if it hits hard enough you can still damage both the gaurds and body.

See there!
04-14-2010 02:59 PM
adawg38 I know what body armor is for. It's to take damage so the body doesn't I'm not stupid. but if you scrape up against rock the plastic will still take the heat. If you take your 3,000lb vehicle and maybe roll down the hill backwards into a boulder I'm sure the steel/aluminum will hold up better like I originally posted but the body can still take a possible dent.
04-14-2010 02:08 PM
03 RUBI The object of armor is to prevent body damage.
04-14-2010 11:52 AM
Levinoss Don't underestimate what the aluminum body armor can withstand.
04-14-2010 11:48 AM
adawg38 The steel or aluminum would definately be alot stronger and take more of a hit but if it hits hard enough you can still damage both the gaurds and body. I like the Bushwackers cause if you hit and get the damage anyway the plastic is not suppose to crack but pop back out so you would only end up with body damage only and the gaurds cover it, The steel or aluminum ones may be alot stronger than I know but I don't have exsperience with those. They both looked good.
04-13-2010 08:50 PM
03 RUBI Take off the plastic corners and replace them with steel or aluminium ones. The plastic type won't protect the body and are mostly for looks.
04-13-2010 08:44 PM
Beer30 Thanks for the input! I think I'll get some more of that 3M adhesive tape and just put it around the top, then trim it. It's mostly the right side that is loose, the left side is held tight by the screws around the gas cap.
04-12-2010 07:45 PM
adawg38 I got a set of those on my 06! Nothing is gonna be 100% air/water tight. Some water will get in there but I wouldn't worry about rust unless you got alot of bare metal hiding under there, besides anything that gets in should run out through the bottom. It shouldn't be real loose either mine fits tight and flush. There is suppose to be sticky adhesive tape all around the gaurd except on the bottom, chances are they might of been trimmed for fit and cut off parts of the adhesive so it doesn't stick very well. You can buy more double sided sticky adhesive and stick it on the outside edging of the gaurds so it will stick to the body more secure.
04-12-2010 03:58 PM
Beer30
Moisture behind Bushwacker guards?

Hi all... great forum you have here! Been lurking for awhile. Just bought my first Wrangler! It's a black 2005 X, 6 spd, 6 cyl.

I did a search for my question but came up empty, so here's my first post. The previous owner left it mostly stock, but put some Bushwacker rear corner guards on. I really like the look of them, however they don't seem to stick on too well in places.

Should I be concerned about moisture (rain, salty road spray, etc.) getting in there between the guard and the body and causing rust? I'd like to keep them on, but not if it's going to rust underneath them.

Any thoughts? Thanks in advance!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:08 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC