|06-21-2012 11:05 AM|
|SJS||did you guys really check that you put 75lbs on the bolts?|
|06-21-2012 07:05 AM|
|06-20-2012 09:36 AM|
|SJ.||The hitch may be one of the easiest things you can do. If you get one with the nuts welded in place, it's a matter of tightening four bolts and plugging in the wires.|
|06-20-2012 09:14 AM|
Are the Quadratec hitches available? The website indicates they are still on backorder.
|06-20-2012 08:51 AM|
|riskyvt||I just installed the Quadratec 2" hitch kit on my '09 JKU. VERY quick install, the wiring harness was plug & play, even had plastic pins along the wiring loom to push into frame holes. Looks like a nice hitch.|
|06-20-2012 06:07 AM|
|SJS||For the wires did u make a hole|
|06-19-2012 02:38 PM|
|khickeyman||I installed the Rugged Ridge hitch and wire harness yesterday. It took all of 30 minutes pretty easy. I did lossen the plastick bumper enough to get the nuts on.|
|06-19-2012 02:12 PM|
|SJS||where did you order it from|
|06-19-2012 01:08 PM|
|06-19-2012 01:03 PM|
I installed the Smittybilt hitch, which as others have mentioned about the RR hitch required me to remove the rear bumper--the nuts were not welded on the bumper side of the hitch and the angle is odd even for a taped up box end wrench. By contrast, taking the bumper off is very easy. I did not have to loosen the muffler.
You'll need a basic socket set and some wrenches.
|06-19-2012 12:54 PM|
|SJS||did you have to remove the exhaust side|
|06-19-2012 10:16 AM|
|06-19-2012 10:04 AM|
I just installed a Rugged Ridge receiver yesterday.
Amazon.com: Rugged Ridge 11580.10 Rear Hitch: Automotive
I did have to remove the bumper because my bolts were not welded to the hitch so I needed the extra clearance. All the hardware was in a separate bag. Perhaps they changed something... dunno.
I could not get the bolts into the holes due to a lack of room on the exhaust side and there was not enough room on the bumper side either. I ended up removing the back bumper, installing the hitch receiver and then re-installing the rear bumper. All in all it took about 30 mins. Simple.
|06-19-2012 09:36 AM|
|SJS||I am going to try to install this soon on my new 2012 JK.. so everyone tells me its a 10min job is that true??? how long did it really take you.... also did anyone do the light kit part>|
|06-10-2012 09:41 PM|
Removing factory hitch from rubicon
My jeep was totaled. I am going to take some stuff off of it tomorrow. Will it come off as easy as the video. What size is the bolt. 2010 rubicon.
|04-15-2010 09:53 PM|
|woodyg||I got the Curt also, piece of cake to install, works great.|
|04-15-2010 04:45 PM|
|oakdale bob||Daggo66 is right, a slim open end wrench on the nut side is tight, but works. Didn't remove(or scratch anything), LOOKS GREAT!! Curt Hitch..|
|04-02-2010 09:45 PM|
|Wrangler010||my nuts aren't welded to the hitch......it came in a rugged ridge box but maybe its really something else.....anyway, i took the bumper off and installed the hitch....the whole process took about 15 minutes....there are 6 bolts that hold the bumper on (16mm) so that was easy.....now i want a new bumper!|
|04-02-2010 09:28 PM|
You shouldn't have to remove anything to install the hitch. It's a 10 minute job tops. The hardest thing is that you many have to wiggle the bolts a little to get them in the hole. As mentioned above the nuts should already be welded on. Make sure your muffler is cool. Here is a video showing the installation. It is not necessary to lower the muffler.
|04-02-2010 04:08 PM|
Taking that plastic bumper skin off, isn't that hard
There are two bolts (16MM ??) inside, up against the steel bumper cross member and two on each side on light duty brackets, should take 10/15 minutes
At least thats the way on my '08 and nothing else should attach toit
|04-02-2010 03:56 PM|
The RR has nuts welded onto the hitch body...So the wrenching is from the other (exhaust side)..
I installed a Curt Hitch after I installed my Rugged Ridge bumper and indeed I had the loosen up the bumper mounting bolts to get the hitch installed over the cross member..
But I don't know the situation with a regular bumper..
|04-02-2010 03:46 PM|
installing a trailer hitch
just got a rugged ridge trailer hitch and attempted to install it......do you have to remove the bumper? there's about an 8th of an inch between the frame and the bumper....doesn't seem possible to get a wrench in here to tighten the bolts......or am i missing something?? thanks!!