|08-31-2014 04:49 PM|
.....what a trip.................
So, this vehicle had a little damage to the passenger side front (right) and has had some parts replaced. this is the side that also [I]seemed[I] to be causing the earlier brake problem. Not sure what to call it, but the cast iron assembly that the calipers bolt to, is a different color (red) than the drivers side. Looks like a replacement part(?). The outside pad doesnt seem to fit between the two cast iron flanges although I can force it in with a hammer but it is then so snug that the caliper has absolutely NO play what so ever. Also, the bolts that hold the calipers in place don't really seem to line up as well as the drivers side (which bolted up and lined up smoothly).
Anyone have any thoughts?
|08-24-2014 11:27 AM|
|jontay||thanks a bunch!!!|
|08-24-2014 09:57 AM|
|08-24-2014 09:16 AM|
|jontay||It also looks like the 1998 year calipers and brake pads are the same ones as recommended for the 2000 year. Same parts for both.|
|08-24-2014 08:44 AM|
Having front brake problems and almost ordered 1999 stuff yesterday but pulled off front rotors and did some measurements first. Sure enough, my hub is 1/2"....on both sides.
Orielly's and NAPA (both online sites) had me buying the 'later' (1999 and after) which were the same part #'s as their 2000 year parts. I think I need the '1999 and before'' which would be the 1998 kit (different rotor part # than the 2000)?
Getting pads, rotors and calipers today and buying the 1998 stuff since my hub height is 1/2". Does this sound right?
|08-21-2014 09:31 PM|
All you guys that give your time, information, experience, help, etc. ........... are just friggin' awesome, Man !!! I've just bought a 1999 TJ and I'm having brake issues so this gives me some ideas and direction to get going on.
Love this website for all the knowledge and expertise.
|11-15-2013 02:41 PM|
|Water Dog||Got my new Black Magic rotors and pads on today and have completed the first 4 steps of the break in procedure. I will finish that tomorrow morning. All I can say is, Wow..! What a difference. It's really nice not to have to fight a pull to one side any longer, and they work great also. I really liked the different sized end clips that allowed for a really nice fit on the pad.|
|11-15-2013 01:19 AM|
Thank you, once again :-)
|11-14-2013 01:51 PM|
Just FYI, the measurement on the old style center hub in Jerry's pic Post#3 is closer to 1/2" rather than 3/4".
|11-14-2013 11:49 AM|
|ellipsis||Thanks WaterDog. I have 01 model. Replaced caliper and brake pads two times and still have little pull towards left side. I'll check the hub size and see if it's a similar issue like '99 model.|
|11-10-2013 10:28 AM|
Yup well known common problem since a lot of the parts computers at auto parts stores are wrong. Gotta match the unit bearings with the rotors. Figure out what you have, then order parts for old style (98) or parts for new style (00).
XJ's had the same issues. The HP D30 I swapped in my LJ was from a 1999 CFC trade-in. Axle was in great condition, including brand new brake pads & rotors. In the process of pulling the knuckles to swap to a Vanco BBK, I discovered why - somebody had installed the wrong unit bearings....one side was new style, one side was old style - with old style rotors. Brakes didn't work on the XJ, so they traded it into CFC. Worked out for me, since I sold the unit bearing, calipers & pads
|11-10-2013 09:42 AM|
The newer rotors will go on the older hubs, but not work correctly (as I found out). If you try putting the older rotors on the newer hubs, it will lock up the wheel.
|11-09-2013 09:28 PM|
|11-09-2013 08:00 PM|
Great Information! I just purchased a 99 and I suspect I have one of each hub. I discovered this because I tried replacing rotors and saw that the two front wheel hubs were very different looking. When I tightened the lugs on my passenger side the rotor smashed against the back break pad. The driver's side worked fine.
I couldn't even figure out how to pose this question to the board so I really appreciate you posting this.
|11-09-2013 08:00 PM|
|wwch99tj||Thanks Jerry that'll help someone who searches later...|
|11-09-2013 07:44 PM|
|Jerry Bransford||Yep, the unit bearing changed dimensions mid-1999.|
|11-09-2013 07:41 PM|
|wwch99tj||Post your measurements here, it'll help someone in the future without having to pm you...|
|11-09-2013 02:53 PM|
Brakes Heads up for 1999 Wrangler Owners
About two years ago with about 120,000 miles on my 1999 Wrangler just after buying it used, I was having an issue with the brakes pulling a little to the left. I pulled all four wheels and replaced both front rotors, calipers, pads, rear shoes, rear drums and rear wheel cylinders. Since my wife works at a local body shop, I had her order the parts from the local Napa dealer using my VIN number.
After the install, although the brakes worked good, I still noticed a slight pull to the right, plus there was always a slight odor of warm brakes particularly on the driver's side. I then replaced the hoses and had the entire system pressure bled and all new fluid installed. The problem remained. I noticed there was a very small notch in the machined seat where the pads rode, so I sanded that smooth, and it didn't really help. I've noticed over the past two years that it pulls less and less often.
Since I'm now using 33" tires, I recently decided to switch out my front brakes to Black Magics and upon visiting their web site, I learned that there was a rotor change made sometime in 1999 that required one to measure their stock rotors to determine whether they had early or late rotors. After some further research, I found that I currently have late (cast) rotors on hubs that were designed for the early (composite) rotors.
That means that while they work, the face of the rotor is sitting approximately 1/4" more to the outboard side and right at the limit of the pad travel. I've found that this 1/4" is what most likely had caused my brakes to run warm (from the extra drag), and as the pads have worn, they don't run warm any longer, but now the rotor is heat checked.
Moral of the story, is if you own a 1999, and need new brakes, Whether you get them from Blaine or anyone else, make sure you check the stock rotor dimensions with the new ones. If you've already changed rotors and don't know if they're right, pm me, I have the early and late hub measurements.