Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Tech Forums > General Jeep Discussion > clutch bleeding

Join Wrangler Forum Today


Thread: clutch bleeding Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-19-2010 08:32 AM
whitebuffalo thanks yall. i ended up just winging it friday night. i could reach the bleeder through the floor hole so i did it one man operation style. only got to do a test drive down the driveway but, its alive again. now if the rain will stop enough to dry things up so i can get some wheeling done before it gets too damned hot.
04-18-2010 10:46 AM
Thuone Heh I'm quoting myself.. Good luck!

Quote:
Originally Posted by Thuone View Post
I had a similar problem. Before you replace your slave cylinder try fixing the cheap stuff.

* Check to see if the spring is still attached to the pedal. Even if there is no pressure the spring will pull it off the floor board.

* Try bleeding your line.. The "fitting right next to the one that is connected with nothing on it" this is your bleeder line. Get a clear jug (1/2 a 2 liter coke bottle) a clear 1/4" tube about 12" long and a 1/4" wrench to loosen your bleeder screw on the end of the fitting that moves. And finally a few bottles of brake fluid. Once you have all this get a buddy to help ya out.

* Remove the cap from the master clutch cylinder behind your firewall and fill your fluid to the very top.

* Put 3" or 4" of brake fluid in your coke bottle place the bottle under the jeep near your fitting.

* Attach the 1/4" tube to the end of your bleeder screw. Shove it over the end as good as you can.

* Put the other end of the tube in the coke bottle. This prevents air from coming back in the line

* Open the bleeder screw this will only take an 1/8 or so of a turn. Fluid should start coming down your tube.

* With your hand start pumping the clutch (Have your buddy stand over the master cylinder dumping fluid in as it drops. If it gets to low it will suck air adding air to the line.) pedal while watching your line under the jeep. Pumping the clutch should force fluid down the line into the coke bottle. If there was air in the line you will see bubbles, keep pumping until fluid is clean and bubble free.

* Tighten your bleeder screw.

Now you’re done bleeding the line remove your hose fill your master cylinder to the correct level and screw on your cap. Good Luck!

If this does not work I would..

* Buy a new master cylinder from advanced or another parts store costs about 80 bucks. (Hanes manual from advanced will show you how to pull you’re old out and replace it) It was really easy. Then you will bleed your lines again. This is how I fixed mine when people were telling me I had a bad clutch and slave cylinder. Hope I explained it well it took a lot of research for me to figure out the best way to bleed your line.
04-18-2010 09:06 AM
jjseel On my '88, it was just like bleeding the brakes, pump and hold while someone loosens the valve...
04-16-2010 10:17 AM
whitebuffalo
clutch bleeding

can someone school me on how to bleed the clutch? i have internal slave, just reinstalled everything last night.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:57 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC