Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > Newbie with fuel gauge question.

Join Wrangler Forum Today

Thread: Newbie with fuel gauge question. Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-06-2007 10:25 PM
nuadu78 no problem
03-06-2007 07:04 AM
Roger_Sausage ^^^^^^^^^^^

That's excellent, thank you
03-05-2007 08:19 PM
nuadu78 To replace the sender unit you have to drop the tank.
But just to let you know, it is a pain in the A..
I had to replace my fuel pump so I know.
But it is doable.
First you have to drive until you tank is almost empty to get rid of the weight.
Then you need to disconnect the battery and release the fuel pressure on the fuel pressure valve (see picture).
Next thing you need to do is to release the fuel tank pressure by removing the gas cap.
Then disconnect the supply line to the tank and also the vent tube (sorry I got no picture of that).
But check the link and you will see what I am talking about.
Ok, now support the tank with a floor jack and remove the nuts which hold the skid plate and the tank (see picture).
BUT do not remove the one with the rubber cap.
These two secure the tank to the skid plate.
If you done that then you can slowly lower your tank.
But you will soon notice that there is not enough space to just lower the tank.
So you will have to work your way trough and around the frame, rear spring, and exhaust pipe.
When you done that, than you can disconnect the fuel supply lines which run to the gas pump (see picture).
Now your tank should be right in front of you !!!
Next thing you do is to remove the nine bolts which secure the fuel pump to the tank (see picture).
Once you done that, just pull the fuel pump out of the tank and you will see the sender unit, it is the big black rectangle (you can see that in on of the pictures as well).
Now you can replace the sender unit.
On other thing, while you got the tank out.
If you don't know how old your fuel pump and fuel filter is, now is a good time to replace it.
And you may want to wash the tank out as well.
If you reinsert the fuel pump into the tank don't forget to use a new seal which is a $1 at your local parts dealer.
03-05-2007 05:57 PM
Dare2BSquare They put clocks in Wranglers back then? My 95 Rio Grande doesn't have one.
03-05-2007 12:38 PM
daddyjeep You most likely have to drop the tank to replace the sender. I haven't done one in a Jeep, but that is most likely the case.
03-05-2007 04:46 AM
Roger_Sausage Thanks for that. The gauge panel itself is pretty ropey so I think I may replace it in the long run anyway, but I've heard that the sender unit on the YJ is a pain to replace?
03-04-2007 10:36 AM
Odd is he I had an 87' where the fuel gauge would work up to 3/4 of a tank, and then would not work from their on out... Just clock your miles and fill up around 150 to 200 miles to be safe..
03-04-2007 03:35 AM
Newbie with fuel gauge question.

Hi all, I'm an English guy currently living out in Bahrain in the Middle East (I know it says Florida but Bahrain wasn't on the list!) and have the chance to own a '91 4.0 YJ 5-Speed. Before I commit though, I'm running it for a week to see if there are any problems. The only major one so far is that the fuel gauge doesn't work at all. I've had a search but I can only find threads relating to incorrect readings, not nothing altogether. Is this a common thing for a '91? All the other gauges work fine apart from the clock, is there still a chance the gauge itself could be faulty though, or is it likely to be the sender unit?

Thanks for your time folks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 08:24 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC