Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Need to replace full steel door with light weight door

Join Wrangler Forum Today


Thread: Need to replace full steel door with light weight door Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-10-2010 01:51 PM
Lenc I have just confirmed by phone with Bestop, that contrary to what I had first been told, their 2-piece soft doors will, in fact, work with the hardtops.

My thanks to all who have taken the time and interest in posting to this request for information.
05-06-2010 02:19 PM
thaduke2003 I was talking about the OEM (Jeep) half-doors. The fit and finish on them will be the best, so they'll keep the weather out more.

The Bestop Element doors with skins and uppers are a viable alternative, but are more of a summer door. For all-season use, I'd stick with the Jeep bits- Mark W.
05-06-2010 01:10 PM
InfernoGirl Third party. They are the Elements half doors from Bestop.


Edit: LOL distorted, I guss we'll have to wait for duke to chime in with what he as talking about!
05-06-2010 01:09 PM
distortedtj ^^^^^ jeep
05-06-2010 01:06 PM
Lenc
Quote:
Originally Posted by thaduke2003 View Post
For either vehicle, a set of OEM half doors and uppers will be the better solution. They're a fair bit lighter than the full doors, and seal well against the weather. The kits for the JK were just released- they'll run around $1600 primered for both doors, windows, and the inner panels. A bit spendy, but NOBODY seems to have ordered theirs from the factory with halfies in the JK (sadly- I wanted them, and there was ONE in the Northeast at the time, and it was sold before I got to check it out ), so you will NOT find them used.

For the TJ, you'll likely be able to find OEM half doors for a whole lot less.
Best of luck! Mark W.
Are the kits you refer to from Jeep or from a third-party vendor?
05-05-2010 09:23 PM
thaduke2003 For either vehicle, a set of OEM half doors and uppers will be the better solution. They're a fair bit lighter than the full doors, and seal well against the weather. The kits for the JK were just released- they'll run around $1600 primered for both doors, windows, and the inner panels. A bit spendy, but NOBODY seems to have ordered theirs from the factory with halfies in the JK (sadly- I wanted them, and there was ONE in the Northeast at the time, and it was sold before I got to check it out ), so you will NOT find them used.

For the TJ, you'll likely be able to find OEM half doors for a whole lot less.
Best of luck! Mark W.
05-05-2010 06:30 PM
Lenc
Need to replace full steel door with light weight door

Hi All,

I work for a water utility that has 2 TJ model Wranglers and 1 JK model Wranglers. They are equipped with hard tops - looks like they are probably from Bestop. All are currently equipped with full steel doors. Our meter readers use these vehicles in the course of their job.

As the Safety Coordinator, I have just learned that they typically drive the Jeeps to the area where they are going to be reading, and then remove the door, placing it in the rear. They do this process to avoid the cold and wet here in Washington they are exposed to while driving to the day's work area.

As the Safety Coordinator, that gives me some heartburn when I think of the ergonomics involved in removing the door then lifting it into the back of the rig. One of our readers recently mashed a finger removing the door from back of the rig.

So . . . I am trying to find a light-weight alternative to the heavy full steel door. Naturally, Bestop says that their doors for their soft top units will not work with the hard top. Do any of you have experience with such a retrofit?

If anyone can point me in the right direction, I and our meter readers would be real happy campers!

Thanks. [I am posting this same thread in both the TJ and JK forums.]

Be safe out there!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:29 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC