Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > DIY body lift

Join Wrangler Forum Today


Thread: DIY body lift Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-06-2007 06:06 AM
debruins just fyi that is for a 2" BL so i would cut it down a little b/c you dont want to have to mess with al the other stuff like the radiator
06-05-2007 05:00 PM
Triple88a
Quote:
Originally Posted by TXST8tj View Post
if he's doing a MML, he won't need the tcase shifter linkage. and even if you did...i wouldn't suggest using it. it causes binding and doesn't shift very well using it. if anything, i'd get a t-case mounted mount.
i removed the rubber bushings on the transfer case bracket that bolts on to the tub and just installed it with out them and added big washers on top, I still used the 2" bl tcase bracket. As you said it will cause binding and wont shift very well.. now it shifts better and easier than stock.
03-13-2007 09:27 AM
TXST8tj if he's doing a MML, he won't need the tcase shifter linkage. and even if you did...i wouldn't suggest using it. it causes binding and doesn't shift very well using it. if anything, i'd get a t-case mounted mount.
03-13-2007 08:29 AM
Triple88a some info on what body lift needs. That image was first introduced to the forum by Nicolas-Eric (thanks man) 932A is for auto tranny. Keep in mind with the bodylift you will need transfer case shifter linkages!!!
03-13-2007 07:39 AM
TXST8tj doing a MML will relieve your vibes. you will be able to ditch the t-case drop.
i've never measured the diameter of my JKS pucks, but they have a thin lip that kinda fits over the stock body mount bushing. i think it more or less keeps the puck centered on the body mount......you could go from there. other kits don't have that lip, they just sit on top of the bushing and are basically the same diameter.
as for the bolts....take a stock one out. measure it and add 1.25" and that's the bolt you need.
aluminum is fine to use. the M.O.R.E. kit uses alum.
the blocks are not all the same size though. the ones to the rear around the gas tank are smaller in diameter IIRC.
the bolts are not all the same diameter either. pull some from the front/middle and pull one from the rear. don't remember the actual size but i know there are only two different sizes.
03-13-2007 06:49 AM
Hank I think we need some more info. Do you currently have a suspension lift? If you're trying to get rid of your t-case drop kit, you should think about a SYE instead of a body lift. The drop kit reduces your drive line vibes and installing a body lift will not help you with this.
03-13-2007 06:24 AM
AussieDave
DIY body lift

going to make my own body lift at work on the lathe.

what diameter are all the blocks?
how many are there?
is aluminum ok to use?
what bolts needed for 1.25" lift?
is there anything else i need?

i'll be doing a motor mount lift at the same time. will this solve my radiator cowl issue?
currently have a 2" BB lift. Will this be enough to get rid of my TC drop kit?

thanx for the help

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 03:26 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC