|05-27-2010 06:42 AM|
Disconnecting the front sway bar also seems to make the offroad ride smoother!
|05-26-2010 07:26 PM|
I ran with quick disconnects for about 7 years, I now wheel with an off-road purpose anti-swaybar similar to Currie's Antirock (AR) but with a setting for street driving. An anti-swaybar like the AR still allow for awesome flex but still manages to have the Jeep in "control" when transversing off camber trails. Had I known what I know now, I wold have invested in an off-road purpose anti-swaybar rather than disconnects.
Here's a link to a video and the actual AR product:
Currie Enterprises 4x4 Rear Ends Antirock
|05-26-2010 01:45 PM|
|05-25-2010 11:04 PM|
With appropriate tools (I use a tie rod end puller, vice grips and a socket wrench) and knowing what you are doing, a front link can be removed and replaced, with new, in 15 minutes and that's with the Jeep sitting on the ground. So, to do the minimum, ie take the lower bolt out (vice grips and socket wrench), is less than 5 minutes a side. Not a big job by any means.
|05-25-2010 10:10 PM|
|03 RUBI||Yea Jerry, good suggestions. I was just trying to point out something that hadn't been mentioned in the posts above mine.|
|05-25-2010 07:15 PM|
|05-25-2010 07:12 PM|
|canadianwizard||except if u put your tire up into your fender and bend everything... watch out the first time or 2 so u know how far u will go.... im running 31's and i can not disconect mine without tires rubbing over taller bumps..|
|05-25-2010 06:02 PM|
|05-25-2010 05:15 PM|
|IndyJeepMan||No damage should come from this? When I go offroad I also have to drive my jeep back home lol.|
|05-25-2010 04:45 PM|
|computeruser||Disconnecting also allows you a smoother off-pavement ride, with less side-to-side jarring over small bumps and such. And it's actually not bad at all disconnected on-road; I regularly leave mine disconnected in town and enjoy the smoother ride over the potholes and irregular pavement. It does require some attention to keep things kosher at highway speeds, though.|
|05-25-2010 03:05 PM|
By the way, disco'ing the front antiswaybar can help when offroad. Don't try the same with the rear antiswaybar, it needs to remain connected. Be sure to reconnect the front antiswaybar before hitting the highway. Older leaf spring Jeeps like CJs and YJs do fine without the antiswaybars but not so with the coil spring TJ.
|05-25-2010 02:55 PM|
|03 RUBI||You will also need to secure the arms to something so they won't flop around.|
|05-24-2010 11:31 PM|
|530ktm||When you disconnect the front sway bar it allows the front axle to flex more which puts the tires on the ground in very rocky or rutty situations. This gives the vehicle better traction which will help you move through the rough terrain. You can disconnect the sway bar by removing the nuts on the bolts and removing them from the sway bar connector which is about 8 inches long. You can swing the connectors up and rest them on the shock tower and this will keep the sway bar out of the way for your trail driving. You need the torx socket and a wrench to take off the nut and bolt which is why they make the quick disconnects for this purpose. I hope this explains what you are asking.|
|05-24-2010 11:30 PM|
The sway bar, when disconnected, allows the axle to articulate to its fullest extent. Works great offroad, but not having it connected can be a hindrance when on-road.
The sway bar's function is to help stabilize the chassis against sway (roll).
|05-24-2010 11:18 PM|
disconnecting sway bar
what does the sway bar enable you to do on or off, and how do you remove it?