|09-28-2010 12:51 PM|
|Kevin925||The #4 fuse is kind of hard to reach. I used a pair of tweezers to get mine out. But takes care of the dome light problem.|
|09-28-2010 10:29 AM|
Pull the fuse. If you've got fat fingers and don't have a fuse puller, borrow your wife's tweezers and pretend you're playing Operation.
I probably won't put the fuse back in when I put the hardtop on. If I need the lights, it's a simple twist of the signal stalk and they're on.
|09-28-2010 04:42 AM|
|09-28-2010 02:03 AM|
|Fofo||I rewired mine with a custom switch as well. However I used a duel post switch because both sides are independent. If you open the passengers door then the light/key chime doesn't go but it does on the drivers side. This is on my 04 tj.|
|09-27-2010 11:32 PM|
I found an easier method than pulling the fuse... if you keep a pretty full glove box like I do (non-valuables), it can be a bit of a chore removing the door of the glove box. Plus unless you keep a fuse puller in the Jeep or have tiny fingers, the fuse is kind of a pain to remove (in a split second).
What I did was unhook my door switch on both sides...I modified the clip on the switch (just shave the little notch off with a pocket knife) so it pops on and off pretty easily and then when I have the doors on, I hook up the driver's side switch. When the doors are off, I unhook it. If I wanted the passenger side one hooked up, I could do it too...takes all of about 5 seconds once you've modified the connector so it pops on and off easily. The switches just pull straight out...or if you feel like you might break the switch reach up from behind and push them out.
|09-27-2010 09:16 PM|
|09-01-2010 09:29 AM|
Quadratec sells a switch with fusetaps and an inline fuse holder. You remove the #4 fuse, put in the taps and put the fuse in the line. Then when you take off your doors you just flip the switch to cut the power. Its $30. You can build one for less, but it's worth the money in my opinion.
Quadratec Exclusive JW-DLB - TJ Dome Light Switch for 97-06 Jeep® Wrangler TJ & Unlimited - Quadratec
|09-01-2010 04:28 AM|
|kpool||alarm on a wrangler???? WTF|
|09-01-2010 03:27 AM|
|bobjenkins||heres my solution|
|06-05-2010 04:27 PM|
|06-05-2010 04:22 PM|
|06-05-2010 02:34 PM|
|osu50sprinter||just pull the fuse!!!|
|06-05-2010 02:22 PM|
|06-05-2010 02:13 PM|
|doclouie||You would think it would not cause problems, but it does. For some reason when the fuse is pulled and the doors are off the alarm will not fully turn on. Not sure why, but that is why I need the springs for the doors. Trust me if I could save the money I would.|
|06-05-2010 02:13 PM|
|06-05-2010 12:56 PM|
I dont see how it could cause problems? That fuse is set up just for the doors nothing else.
I guess people dont like saving money and just doing the easy fixes. Ive taken my fuse out and left it out, I dont need a light to be on to step in my Jeep.
|06-05-2010 11:48 AM|
|doclouie||I am getting the springs for the doors as it causes weird problems with my alarm system, but I am sure that is just my Jeep.|
|06-05-2010 11:09 AM|
I had the same problem so I wired in a regular toggle on/off switch and mounted that in the center dash near the O/D on/off switch. It took me about an hour and I already had switches and wire so it was free. If you'd like me to send you DIY instructions, shopping list and pics, i'd be glad to do so. just let me know.
This method is a lot quicker and cheaper, in my opinion, then buying those springs they sell, but that's just because I love messing with electrical things
|06-05-2010 09:38 AM|
|alstjruby03||yes fuse 4 works great.i agree with jerry how hard is it to pull a fuse?|
|06-05-2010 09:30 AM|
|pakman55||im pretty sure that its in the owners manuel.|
|06-05-2010 08:59 AM|
|McGridDLe||i have an 06 TJ and on mine its the very bottom right fuse. on the back of the glove box there is a guide, and it either says dome light or something that has to do with the doors, its raining or i would go check for you. but I pulled mine and just leave it out all the time, wheather i have doors or not.|
|06-04-2010 10:56 PM|
|radar||put a $2.00 switch on mine now i don't have to pull that fuse|
|06-04-2010 10:20 PM|
|Pleiner87||I picked up a fuse puller from a random car at the junkyard to pull mine fuse... and it was free!!!|
|06-04-2010 09:50 PM|
|doclouie||Fuse #4 in the bottom right of the panel.|
|06-04-2010 08:29 PM|
|nick50471||The fuse is not difficult if you have small hands. I have my wife pull the fuse. That is even easier.|
|06-04-2010 08:07 PM|
I dunno how installing two spring clips you have to order from Quadratec can be easier than pulling a single stupid little fuse put there for this specific purpose. The Jeep engineers specifically designed that fuse to only disable the door jamb switches, not the overhead light itself. The interior lights can still be turned on by the usual dashlight dimmer control after the fuse has been pulled.
I can't figure out for the life of me how anyone can figure pulling the #4 fuse is so difficult. Maybe for those who have to pay others to do everything on their Jeep? I dunno.
|06-04-2010 07:52 PM|
Quadratech carries a set of "springs" for just a few dollars which will clip to the door switch when your doors are off, essentially telling the jeep that the doors are closed and thus keeps the dome light off. WAY easier than pulling fuses
|06-04-2010 06:26 PM|
|OklaTJ||lol mine has never worked!|
|06-04-2010 06:25 PM|
|pakman55||no worries. if you cant find it i have a picture that i got from the forum.|
|06-04-2010 06:24 PM|
Lol i did use it but the only thing that came up was a wire set up for an on off switch in a YJ. Thanks for the help though dude.
|This thread has more than 30 replies. Click here to review the whole thread.|