Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Need help on painting bumpers and running boards.

Join Wrangler Forum Today


Thread: Need help on painting bumpers and running boards. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-20-2010 12:09 PM
jayc That came out good. that was just the spray on bed liner?
06-20-2010 04:08 AM
dkswift That does look really nice.
06-20-2010 01:41 AM
philliprose25 I just finished the project, take a look at my profile pics. Used the recomended Rustoleum Truck Bed Liner Spray. Looks fantastic. Thanks for everyones help!
06-15-2010 11:30 AM
SurfNaked2010
Quote:
Originally Posted by CubbieBlue View Post
I am glad you posted this thread as I am planning on doing the same thing this week/next.

You do not need to sand down to bare metal, do you? What grit sand paper?
No you dont NEED to you can just sand it enough for it to stick but i wanted to take it down to bare metal because had some rust and a lot of chipping the time and effort and sanding pads is worth the $100 i spent on getting both front and rear tube fenders sand blasted. it all depends on how bad the paint is already.
06-15-2010 11:26 AM
CubbieBlue I am glad you posted this thread as I am planning on doing the same thing this week/next.

You do not need to sand down to bare metal, do you? What grit sand paper?
06-15-2010 10:59 AM
T-BONE N BIXBY
Quote:
Originally Posted by philliprose25 View Post
where can i buy truck bedliner at? Home Depot?
Lowe's carries it. Rustoleum Truck Bed Liner Spray Paint. About $5 or $6 a can. Autozone has it too but it's a little higher priced.
It's in a taller can than normal spray paint and it sprays EXTREMELY SMOOTH.
My front grill and headlight beezles are painted with it and it has stood up to all rocks that have been thrown at it. (been about 1 1/2 yrs) The paint hasn't really faded at all, but since it's such a simple job, I plan on putting another coat on it soon. I just masked off around the fenders, and stuck some cardboard in front of the radiator.
Also, I recently replaced my old, broken tailgate and purchased a used one that was more structurally sound. I plan on painting it with the truck bed liner paint as well.
My jeep is dark blue, with a black grill and black tailgate. (can't really see the tailgate because the spare tire covers most of it)
06-15-2010 10:37 AM
SurfNaked2010 i got my herculiner at walmart im doing my tube fenders right now. they had rust and chipping powdercoat on them so i just took em to a place to sand blast everything $100 bucks is fine for me got em used for reallllll cheap. than ill just coat em with herculiner.
06-15-2010 10:30 AM
philliprose25 where can i buy truck bedliner at? Home Depot?
06-15-2010 12:40 AM
wasurfer86 if i were you id use truck bed liner instead of paint of powder coat.
06-15-2010 12:33 AM
dkswift Seems like every time I get hammered something ends up being painted flat black lol
06-15-2010 12:32 AM
philliprose25 So use those instructions and THEN sand. Guess I'll use the same steps to clean it again after sanding. Thanks!
06-14-2010 11:18 PM
drivebytruckerz Before sanding: scrub with a brush and use water and Comet instead of soap... This will get any "anti-paint" stuff like stray armorall, oil, fluids and the like off and keep it from being sanded into the metal, which would repel paint and make it bubble up. A tip my dad taught me. He used to run the body shop at a Ford dealer.
06-14-2010 11:13 PM
philliprose25
Need help on painting bumpers and running boards.

I want to paint both my front and rear bumpers as well as my running boards. All parts are the "tube" kind and all are currently chrome. I'd like them all powder coated black but I don't know who could do that around me (Westminster, MD) so I am gonna go with either a flat black or a hammered finish. MY plan so far is:

1. Remove all pieces
2. Sand down to metal
3. Clean all pieces to remove dust and dirt.
4. Apply 2 light coats of primer with light sanding in-between
5. Apply 4 coats of flat black or hammered finish paint

Any advice would be appreciated and I will definitely post a "how to" with pics when the project is complete. Thanks in advance.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:19 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC