Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > General Tech Forums > Builders Corner > Best homemade Hi-lift jack hood mount!

Join Wrangler Forum Today


Thread: Best homemade Hi-lift jack hood mount! Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-11-2010 09:31 PM
XJSean Nice
06-21-2010 06:50 PM
Coyote_94YJ Sweet mod. I might have to give that a try.
06-21-2010 06:33 PM
jr. i like it, good job !
06-21-2010 04:10 PM
hannahuffster
Best homemade Hi-lift jack hood mount!

I USE my jeep! We rock crawl and trail ride almost every week. I wanted a tough hi-lift mount that was out of the way, out of the danger zone (bumpers), and outside the tub [wouldnt want that thing coming loose in a roll-over situation].

I made my jack mount out of a few tiny pieces of scrap 1/8" steel flat stock I had on hand, the rubber spare tire bumpers on your back gate, and $8 worth of hardware from home depot.


Notice it is low-profile. It can be seen from the drivers seat, but doesnt enter fear with your line of sight. Also it is in a posisition where the hood can still lay back against the windshield frame without the jack touching the glass or the jack base hitting my drivers side spot light.

Here is the parts that you will need:
  • 1 - 10" piece of 3/8 all thread (to be cut into 2 - 5" pieces)
  • 4 - 3/8 nuts
  • 2 - 3/8 lock washers
  • 2 - 3/8 wing nuts
  • 2 - 3/8 fender washers
  • 2 - 5/16 x 1 carrage bolts
  • 2 - 5/16 nuts
  • 2 - 5/16 lock washers
  • your rubber spare tire bumpers
  • 2 - 1/8 x 2 x approx 5 flat steel stock (or scrap pieces of metal)
  • 1 - 1/8 x approx 1 x approx 5 flat stock steel scrap
  • 2 - auto vacuum caps
  • 1 - padlock


Here is the drivers side photo.

You will have to take a small pick or screwdriver and remove the metal washers that are recessed inside of the spare tire bumpers for them to fit over the all thread. The 3/8 nut will recess inside the [bottom] rubber bumpers with minimal force.


Here is the passenger side photo - notice the lock plate.

Take your 1" flat stock and scribe a line down the center (long ways) to center the hole to be drilled so a lock shank will fit through it. Then start taking metal off each edge with a bench grinder until it will pass through a hole in the hi-lift. Once done figure your carriage bolt hole and make the bend with a vice, keeping it on your flat stock under the hood [pictured below].


1/8 X 2 inch flat stock used under the hood for support and security.

Assemble everything in this order (starting under the hood and working your way up) on each piece of the all thread: NUT - LOCK WASHER - UNDER HOOD SUPPORT METAL - JEEP HOOD - RUBBER TIRE BUMPER - NUT - JACK - RUBBER TIRE BUMPER - FENDER WASHER - WING NUT - VACUUM CAP (TO HELP PROTECT THE THREADS)

If you wanted to spend about 4 times the money you could build it all out of stainless if you wanted. Took me about 2 hours starting from scratch to throw this thing together. Hope you like and Enjoy!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 12:30 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC