|12-30-2010 09:24 PM|
I have a 1993 YJ
I am trying to find a solution for the gap between the post on my roll bar behind front seats and the soft upper. Does anyone know where I can buy these, I'm going nuts with this. I tried the TJ gap filler, doesn't work. Any suggestions?
I have added a pic of the gap behind the upper on my 93 YJ.
|12-29-2010 10:28 AM|
|12-28-2010 11:43 PM|
|12-28-2010 10:12 PM|
|12-28-2010 10:06 PM|
|12-28-2010 09:33 PM|
|12-28-2010 05:03 PM|
|12-28-2010 02:16 PM|
Here is a sot of the front top, you can see the self tapping sheet metal bolts, and a side view of my YJ.
Hope this helps
|12-28-2010 07:54 AM|
|mykel_ls||I am trying to find a solution for the gap between the post on my roll bar behind front seats and the soft upper. Does anyone know where I can buy these, I'm going nuts with this. Thanks.|
|07-02-2010 12:44 PM|
|4Jeepn||The holes where gone on my cj hardtop.. I would set it on the windshield and the get some silicone and run a line then use some duck tape over that.. end of season just pulled the duck tape off and clean up the silicone. Held well enough to keep the water out and top on.|
|07-02-2010 12:10 PM|
Just bought a hard top myself for the winter. We put it on to check the fit. It fit pretty good other than the channel for the bikini top that will have to come off.
I did notice the holes that would be used along the windshield are ripped out on mine as well. Curious to see if any has had to fix that problem on their own and been successful.
|07-01-2010 08:06 PM|
No replies, need help
Does anyone have a pic of the inside of their yj where the hardtop meets the windshield? I don't see anything that I can screw the top to up there.
|06-24-2010 08:03 AM|
Can someone take a picture of their hardtop on their yj from the inside. Just wondering what I should be looking at where the top meet the windshield frame. I think I might be overlooking something. I can't seem to find anything I can screw the top into. I even bought the reinforcement strips from quadratec, but I don't know what they are supposed to mount to on the frame.
|06-15-2010 09:09 PM|
Thanks for the info on the door uppers. I did remove the channel from the soft top. There are a bunch of holes that look like they've been ripped out on the hard top near the windshield. Is there anything made to reinforce fiberglass of the front of the hard top? I'm afraid if i just put more screws into the top that they will just rip through the fiberglass as well.
Any pics of that area would also be greatly appreciated.
Thanks everybody, this forum is the best.
|06-15-2010 11:21 AM|
they do make half door uppers, here is an example. You'll need the curved corners -vs- the pointed ones.
This one also has the gap filler behind it to close in the roll bar, you won't need that with a hardtop, just the top half of the door.
|06-15-2010 11:16 AM|
I had to run (3) self tappers into my 94' from the inside. One in the center and a couple more out about a foot to each side. And yeah, make sure you remove the soft top slider on top of the windshield frame.
before winter, I want to pull it back off and seal the edge with a piece of weather stripping then seat it back on there and screw it back down.
|06-15-2010 10:52 AM|
|Razorus||and there should be a few holes up along the front on the inside where you can run some self-tappers into. Otherwise it fits pretty snug on its own.|
|06-15-2010 06:18 AM|
|hannahuffster||Should mount right along the top of the windshield frame. Will have to take your soft top channel off first for it to fit though...|
|06-15-2010 01:05 AM|
|CMEvans79||I'm not a YJ guy ... but I have seen people talking about "Screwing" their tops on ... I'd check into that ...|
|06-15-2010 12:18 AM|
Hard Top Questions?
I just bought a hard top and full steel doors for my 93 yj for $250. The top has a few cracks in the fiberglass right at the bottom where it sits against the rear corner panel.
My issue is that I have bolted the top down around the rear area of the jeep, using the existing soft top mounting spots. I can't find any mounting places up against the windshield area. Is there something I'm missing or is there in fact no mounting to the window area.
Also the full steel doors need everything except the glass and crank replaced. I still have my original half doors with soft uppers, but they dont fit w/ the hard top. Does anyone make a half door upper that will work with the hard top?