Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > YJ Jeep Wrangler Forum > YJ Tech Forum > YJ Brake lights (only) not working

Join Wrangler Forum Today


Thread: YJ Brake lights (only) not working Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-16-2013 07:59 AM
Mowrangler Melted fuses are commonly caused by a bad connection at the fuse holder, corrosion where the fuse plugs in will cause excessive heat melting the fuse it self.
12-15-2013 04:11 PM
garimusprime Thanks again for your help!!!
12-15-2013 03:08 PM
johnsonken1332 melted...probably from higher amp fuse in block to run other accessories such as lights..etc done people just have no idea
12-15-2013 02:33 PM
garimusprime FIXED! So check this out - I went out and looked at the fuseblock - and the one marked STOP - as you recommended didn't have a fuse in it - which is why I missed it before (as to why, I have NO idea). However, I did notice that it's melted a bit around that fuse - so I'm going to need to get that checked out. Popped a 15a fuse in and voila! My brake lights are working again.

I have NO earthly idea where the fuse went or why it clearly shows some melting - I know my mechanic mentioned it about a month ago but said it didn't appear to have any obvious shorts - maybe it's been out that long... weird.

But it's fixed now. Probably need to replace the block just to be proactive. I'm sure it happened before I bought it a few years ago.

Thanks!
12-15-2013 02:20 PM
Jkilbert You're correct that if your signal work on the rear then the bulbs are good. Definitely check for power at the switch and for functionality of the switch. They have been known to be bad out of the box
12-15-2013 02:07 PM
garimusprime Thanks for the quick reply! So here's a qustion - and i always want to check the simple things first -but if the lights were blown - wouldn't the turn signals not work - or is that something different in the bulbs?
12-15-2013 01:42 PM
johnsonken1332 check wire continuity in switch pedal wires one is probably either damaged...check lights make sure they are not blown. check fuse labled stop..not park. alot if times the 12v wire works its way away from fuse panel
12-15-2013 01:38 PM
garimusprime
YJ Brake lights (only) not working

I recently discovered that the brake lights on my 93 YJ quit working. I replaced t he switch at the pedal - that didn't seem to fix it. Turn signals, reverse and running lights all work fine, but only my brake lights have quit working. I checked all my fuses, but can't seem to find one that is blown. Any suggestions for where to look next?

Thanks!
GarimusPrime

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:47 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC