|07-27-2014 06:32 PM|
|07-26-2014 01:01 AM|
|07-26-2014 12:00 AM|
|07-25-2014 09:35 PM|
|Majnoon||Wow. That's a big azz box! I like it. Hey performance gains will not exist but damn that box is nice. Could fit lots in that.|
|07-25-2014 09:28 PM|
I was considering this intake not for the gains but for the extra storage space. They have a box that goes in the place of the airbox that you can put stuff in. Not really sure if it would be big enough to stow anything useful in. Just looking for some decent options for extra gear since I usually have the gf in the other seat and the dog in the back (don't need everything rolling around nor do I have a lot of room with the dog in the back). Here is a link to what I'm talking about. Are there any other decent options? I was also looking into the molle attachments that bolt into the tailgate but my rear hatch leaks slightly with a lot of rain so it any gear could potentially get wet.
Spectre Performance 99431 Storage Box | eBay
|07-25-2014 01:05 PM|
|jeepermcclure11||Yeah it will! Its the same O.D. on the throttle body|
|07-25-2014 12:15 PM|
|jeepermcclure11||Spectre is a good option if you get the river raider cowl snorkel!! It adds a filter to that snorkel and if you dont like the look of the Traditional snorkel river raider is sweet|
|10-23-2011 07:29 PM|
|2JeepsThatRun||Does any one know if this would fit on a 2.5l with a 4.0s throttle body?|
|09-02-2011 10:43 AM|
|IslandTJ||Meh, IMO the only reason to replace a Jeep's stock airbox is to make space for OBA. Anything else, is time and money expended.|
|09-02-2011 10:24 AM|
1. make room for a fender lift.
2. too lazy to find junk yard parts that fit.
3. another reason to play with the dyno and verify, or call BS on their claims.
4. To get fresh cowl cold air.
#4 is the best reason for a cowl intake. My IATs dropped substantially and run about 10* over ambient. This will cause a gain in hp under certain conditions that would be difficult or impossible to measure on the dyno. It really lowers the IATs while going slow offroading. I have seen IATs of 175F while the stock intake is sucking that nice fresh air off the back of the radiator.
I'm going to install a 90* elbow inside the cowl to cut down on the sound, and install one of the cab filter cowl scoop things (maybe 2 of them). Then I'll have a double filter, and the in-cab HVAC will be filtered as well.
Here is my testing data.
Jeep Wrangler 18 dyno pulls for CAI testing - Trick Tuners Forums
|09-01-2011 03:51 PM|
Here where you can pick up the mushroom snorkel head.
Tisco Tractor Part Mart: Reliable Tractor Parts You Need. Fast :: PRECLEANER (C5NN9A660A)
Matt Savage Land Rover Parts Raised Air Intakes
|04-11-2011 09:11 PM|
I bought an 04 TJ Unlim. which had one already installed. I owned a '00 sport before this. Same engine. I DO notice a difference between the acceleration of this jeep vs my other. What I'm looking for now is a way to snorkel this sucker so that I don't have to keep cleaning my air filter every time I get muddy. Something to think about though is IF it does introduce cooler air, this will definately help over the life of the engine. You add a louvered hood and you may extend the life of your engine for many miles.
|03-25-2011 11:27 PM|
|99TJCrawler||I have one of these. It will not get you better mileage.|
|03-25-2011 10:38 PM|
|s3nt3nc3d||What mixture? Our engines are fuel injected, not carbureted. The intake only allows air into the system...the air and fuel aren't mixed until they enter the cylinders. A cold-air intake on our engines will have no significant effects on fuel economy.|
|03-25-2011 09:45 PM|
|eric_b993||Does anyone know what this does for mileage? It should increase efficiency by making the mixture burn better, but does it?|
|01-29-2011 11:13 PM|
|99TJCrawler||Just installed it yesterday. I don't feel a real difference to be honest. I didn't expect a lot out of it. The throttle response seems a little snappier. The biggest benefit for me, as I stated earlier, was gaining the space where the intake box used to be. Right now, I'm working on how to turn this into a snorkel. Shouldn't be too difficult to do. Just so you know, the hole you need to drill in the firewall IS NOT in the dead center. Make sure to read the instructions. I did not read them but fortunately, I made the hole on the passenger side anyways lol. That could have been really bad. Like I said, instructions are your friend. Overall, the install was very simple. It makes it easier if you take off the hood also. Anyone know where I can get a snorkel head from w/o having to buy the kit?|
|01-27-2011 05:57 PM|
thanks six gun matt, and 99 tj crawler, i was guessing to use black silicone, please get back to us and let us know how you like it, does it make noise, etc.
thanks again, i live vicariously through you until i can do this to mine. (still at engine shop in pieces) week 4 now
|01-27-2011 05:52 PM|
|99TJCrawler||Holy crap! That is awesome! Your going to put a freaking welder where the air box was?! Your like a mad scientist or something! Now I want a damn welder on my car! Make sure to post those pics!|
|01-27-2011 01:53 PM|
|acrijos||I am using the spectre as the basis for home built hummer type snorkel. I cannot install a "normal" snorkel as the ARB as I have a Premier Power Welder in the place where the OEM airbox used to be. As soon as I finish, I will post pictures.|
|01-27-2011 12:32 PM|
|99TJCrawler||Btw, drilling the hole isn't that big of a deal. Just make sure the hole is the size of the tubing, (3") and use black silicone gasket maker to make a seal on it. The tubing does not go into the passenger compartment and you will not be drilling into the passenger compartment so it will not cause problems.|
|01-27-2011 12:28 PM|
|99TJCrawler||I am installing it sometime this week so I will give you some feedback on it.|
|01-27-2011 10:01 AM|
|Six Gun Matt||Spectre actually installed one on my TJ, as noted above. Yes, it does make a whistling noise at certain points related to RPMs, speed, and throttle position. It's not really a constant loud whistling, but there is a very slight constant hissing. It doesn't bother me at all, I think it sounds kinda cool, but that's just me. It's not like you have to wear ear plugs or anything. In fact my exhaust is far more distracting than the intake. But be prepared for some sort of noise, it's a given.|
|01-27-2011 08:59 AM|
|sandro||99TJCrawler, Please tell me, does it make that hissing sound I read about? Is there anything at all as far as throttle response? Anything? I'm very reluctant to cut a hole in my firewall, but this seems like true cold air, vs. the K&N style cone under the hood type? I know my truck runs better on a cold morning, so i was hoping this would help my jeep just a hair? Any input you have is appreciated, thanks|
|01-26-2011 09:48 PM|
|99TJCrawler||I just bought one of these and I understand where you guys are coming from. The reason that I bought it was 1) as stated previously, it frees up that space where the air box used to be so that I can finally put in my manifold for my on board air, 2) It seems pretty simple to make a snorkel from this kit if you were to run some tubing under the cowl and up the passenger side and if you ever wanted to get rid of it, you could just replace the cowl panel instead of your fender. Little cheaper than buying a snorkel and looks better. If I was suggesting this kit to someone, or any kit for that matter, I would tell them not to expect any horsepower.|
|01-26-2011 07:34 PM|
|sandro||I like the idea of cold air...i like the idea of a higher intake... i DON'T want anything loud, and i've read that these things can make a hissing sound that is audible from the cabin while driving? Having said that...I'm the guy who would paint a pink stripe on my hood and paste a michael jackson bumper sticker on if it would give me another 10 horse power, so... if anyone has one of these things, please let us know what you think ! Also, I am intrigued about the idea of having a couple of beers and cutting a 3" hole in my firewall with a saws all....that can never be fixed...idk|
|07-13-2010 02:18 PM|
|Six Gun Matt||
All the more reason I never even considered this mod before. But I do have to say I was more intrigued by the other features I mentioned before and schnutzy pointed out another feature that will prove beneficial when I move forward with body armor. The added bonus of potential power increase is nice, but at least to me, is the lowest on the list of benefits.
|07-13-2010 01:08 PM|
|schnutzy||the only reason i see to instal an aftermarket intake, is if you have high clearance tube fenders that cause the stock intake to no longer fit.|
|07-13-2010 01:05 PM|
First, dyno tests not exactly highly accurate or repeatable... you can run the same engine three different times through a dyno and get three different results. Second, dyno tests are VERY easily manipulated to produce the results you want to show. Third, even the couple 4x4 magazine tests I have read showing some sort of dyno gain with aftermarket air intakes never showed gains anywhere near 11 hp. And finally, 4x4 magazines never tested an advertiser's product they didn't like so it's not like even those tests are reliable.
The TJ's air intake is completely free breathing with no restrictions like some engines have. So when the factory OE air intake system is already capable of delivering more air than the engine can consume, offering it more air won't make a difference.
Installing an aftermarket air intake onto a 4.0L engine is, in my personal opinion, like inserting a big funnel into your mouth in the belief you'll be able to breathe more air in and thus be able to run faster.
|07-13-2010 10:16 AM|
|Six Gun Matt||
Well, I have to chime in here, because I was actually the lucky one that was picked by Spectre for a magazine article install of this exact system. I had always said that I wouldn't want to spend money on a CAI, so when the opportunity rose to try this out, I was very curious. Before and after Dyno tests showed 11 hp gain over stock, which is noticeable. There are a couple of other advantages other than just horse power gains, such as opening up the stock air box location to allow for the (future) install of a York compressor system in addition to my existing a/c system using the Kilby kit, which wouldn't be possible without modifying the air box.
It also does raise the air inlet point by several inches, which actually does decrease the risk of sucking up water when going through deeper water. Where this system actually enters the cowl is not directly under the openings in the cowl, so rain and water coming over the hood is not as likely to enter the system as you might think. Besides, if you are going through deep enough water that you would have water over the hood, your stock air box is already under water. A splash of water over the hood would not get into the air system easily.
So if someone asked me if I would pay for this or do it again, it's hard to say. There are so many other things to do on my list that this probably wouldn't take priority. But if you were looking to do a CAI I think this system is better than the other CAI systems out there that use the stock filter location.
|07-12-2010 03:10 PM|
|530ktm||That thing is a joke.|
|This thread has more than 30 replies. Click here to review the whole thread.|