Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Bad Plugs?

Join Wrangler Forum Today


Thread: Bad Plugs? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-18-2006 10:56 AM
Jerry Bransford
Quote:
Originally Posted by dcrolin
Any suggestions or fixes for this code 43 I am getting??
Only the same one I already suggested to you above. There is usually no other fix for repeated 43 codes.
01-18-2006 08:17 AM
dcrolin Any suggestions or fixes for this code 43 I am getting??
01-17-2006 05:22 AM
dcrolin Mine is a 97...Sahara model...AT...Now I am getting a noise for a few seconds when I put it in reverse right after start up....cold weather start up. Could this be related??
01-16-2006 11:53 AM
Jerry Bransford
Quote:
Originally Posted by dcrolin
Also, about the TSB... I'm not sure how they work, I am not the original owner, so could I still take it to the dealership and they would do it for free? Thanks
TSBs are not the same as a Recall. Recalls are always done for free whether or not the vehicle is under warranty. Recalls are for serious defects, usually safety related. TSBs are a Technical Service Bulletin that offers the dealer a prescribed method to fix a common problem and but are not free unless it's under warranty.

Your TJ is newer so it's hard to say if the weak valve spring batch problem is the source of your misfire as it was for my '97.
01-16-2006 04:48 AM
dcrolin Also, about the TSB... I'm not sure how they work, I am not the original owner, so could I still take it to the dealership and they would do it for free? Thanks
01-16-2006 04:38 AM
dcrolin The CEL just came back on today...I'm assuming its the same code...I don't have a scanner...and I haven't had time to take it to Autozone for the read. As far as the plug being fouled, when I changed the plug the other day...the one I took out (installed 6 months ago) was worn at the tip...there were no deposits, but the tip was just rounded and worn down. Question...to reset the computer, just unplug negative terminal or is there a hazard fuse I should pull?? B/C I always unplug negative terminal when doing work so that should have reset the ECU. Also could the constant CEL be from not having enough torque on the plug...b/c this time when I replaced the plug I didn't torque to spec....The #1 plug is hard enough to get at w/ a hinged socket adapter but I've already broke the porcelan before trying to torque. Thanks for the input and keep it comin.
01-15-2006 12:23 PM
Jerry Bransford Some 97/early 98 4.0L engines had bad valve springs installed from a bad batch. If this problem persists, that is likely your engine's real problem. The dealer has a TSB for it which basically just replaces the valve springs.
01-15-2006 10:45 AM
Fapple I have had the same problem with my 2003 TJ. I was going up a hill in 5th gear talking to the wife, should have down shifted but hadn't yet, just mashed harder on the gas peddle. then the check engine light came on. It was also a #1 cylinder misfire. I did not change the sparkplug, I just reset the computer. it's been 7-8 months now with no problem. I wrote it off as an computer (or software) glitch. When is your light coming on, is it during a heavy load on the engine? When you change your plug is it actually fouled? I have an OBDII scanner and when I hook it up to my Chevy Tahoe it gives me a count of how many times each cylinder has misfired. The point is misfires are not a problem... too many misfires are a problem. Who knows what the algorithm is that the Jeep computer is using to turn on the check engine light for misfires. If it happens again (if I were you) I would try an experiment. I would just reset the computer and see how long it takes to get check engine light again.


Well, good luck keep us posted...Thanks,
Frank
01-15-2006 02:31 AM
dcrolin
Bad Plugs?

Hello Everyone...I have a 97 TJ 4.0 AT with 135K miles...Here is my problem...I just got a CEL code 301 -- Cylinder #1 misfire. So I replaced the #1 plug and CEL went away. About 6 months ago I had the same problem...same solution...same result. My question is what would be causing my #1 plug to do this. I did a complete tune-up 6 months ago...new plugs, wires, cap, rotor. Could it be a bad injector?? Why just #1 plug foul?? Any insight would be greatly appreciated. Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:23 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC