Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > JBA Header

Join Wrangler Forum Today

Thread: JBA Header Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-11-2010 03:41 PM
aGERBIL I had an 02 tj. Loved it. I have three u2 sensors that I can find. Three cats too. It's insane. Would one of those performance chips work the kinks out? A guy with an 04 jeep rubicon did that with his. I'm not sure if he too the o2 sensor out, but he dd the cat converter.
08-10-2010 03:16 AM
Jerry Bransford
Originally Posted by AzTJ View Post
I donno Jerry, part of me thinks you should have bought a buggy.
Yeah wouldn't that be sweet. I miss my far simpler '97 TJ, that is for sure.
08-10-2010 02:58 AM
AzTJ I donno Jerry, part of me thinks you should have bought a buggy.
08-10-2010 02:45 AM
Jerry Bransford
Originally Posted by AzTJ View Post
^ did not know that. Pretty lame IMO.
Tell me about it, my '04 TJ has more cats and 02 sensors than I know what to do with. And one of the 02 sensors is apparently bad (causing a CEL) but it's so far down on my priority list that I haven't had a chance to determine which one it is and if it's really bad or just bad wiring.
08-10-2010 02:41 AM
AzTJ ^ did not know that. Pretty lame IMO.
08-10-2010 02:32 AM
Jerry Bransford As opposed to earlier TJs where there was just one, there are now four catalytic converters on newer TJs and removing any of them will just cause the computer to get upset and generate a Check Engine Light.
08-10-2010 12:31 AM
AzTJ Third cat? There should only be one... As far as the 02 sensor goes, it's needed for the PCM to control air-fuel ratio. I wouldn't mess with it IMO.
08-09-2010 08:21 PM
aGERBIL Thanks. Some of my mechanic buddies said the same thing. It was a suppose to be a 3-4 hour job, but it took us about 12 hours and it was dark and raining so we might have sped things up a bit. I'll take a look at it. Thanks for the quick response. This place looks to be more usefull than stupid schucks!!

With that, I was told by a fellow Jeeper up here in AK about the 04-06 unlimiteds, that you can cut that third cat and take the o2 sensor out and put a straight pipe from there to the flange that ends under the transfer case cover. How easy is that? Is is something like a beginner like me should do. I love learning as I work on things, but also to be prepared. I'm new to this so I may label certain parts wrong, my bad, I'll learn.
08-09-2010 04:17 PM
AzTJ ^x2 I did that 2 weeks ago on my mother's XJ. I noticed it before we fired it back up though. There was a large gap on intake #5. So I loosened it back up and wiggled it and it fell into place on those alignment studs on the head.
08-09-2010 04:14 PM
Jerry Bransford Your intake manifold was not reinstalled into the correct position. There are a pair of small positioning points on the head that the intake manifold has to be positioned over. If it's not, a large vacuum leak will be present and your engine rpms will be sky-high.

Loosen your intake manifold, reposition it correctly and tighten it down per the FSM tightening order and torque values and your problem will be cured.

And a big welcome to WF!
08-09-2010 03:34 PM
JBA Header

I just recently installed a header for my jeep. It's a 2006 Rubicon Unlimited. I have just put everything together. All plugs, as far as I had them labeled, are put in the same spot, vaccum hoses and all. I've tighted everything down to the letter. I went to start it up, and the throttle just opens wide open. I don't know why it would do that. I'm use to the old carburetors, so I'm unfamiliar with the electronic stuff. Is there a possibility that I didn't seat the intake manifold on correctly? What's the best way to reach those bolts with out dropping the exahust system? Any help or where to trouble shoot?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -5. The time now is 01:44 AM.

Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC. is not in any way associated with the Chrysler Motors LLC