|05-14-2014 04:03 PM|
|05-14-2014 12:47 PM|
Once you remove the slave from the bell housing, you can take a couple of quick measurements and see if anything is way off. Here is approximately what they should be. If your release arm measurement is very much larger than what is pictured, your release (throw out) bearing, your pressure plate, or both are toast and you need a clutch replacement.
|05-14-2014 12:27 PM|
|08-12-2010 12:11 PM|
|GoodsOfLiveng||Problem Solved, thank you so much to everyone!|
|08-12-2010 11:50 AM|
|08-12-2010 11:49 AM|
|Indy||Pump the pedal 20-30 times real fast. Add more oil if needed. Check for any leaks (follow the line from where you put the brake oil in to the bottom of transmission).|
|08-12-2010 11:44 AM|
|08-12-2010 11:27 AM|
|Gate53||Pump the cluch to the floor for awhile a see if pressure returns.|
|08-12-2010 11:00 AM|
|GoodsOfLiveng||So I added more clutch fluid and it didn't fix the problem. Do I have to let it sit a little bit or should it fix the problem immediately?|
|08-11-2010 11:07 PM|
|GoodsOfLiveng||Looks like I am very low on clutch fluid! Unfortunately NJ law doesn't let me drive after 11 and neither will my mom so I will have to see if it works tomorrow morning, but I feel much better, I'm pretty sure that was the problem. Thanks a ton for the help Ken Steele I feel 100 times better knowing I will still be able to drive my jeep around and feel awesome.|
|08-11-2010 10:45 PM|
|08-11-2010 10:22 PM|
|Ken Steele||You have a hydraulic clutch. Check the fluid. The clutch master cylinder is under the hood beside the brake booster mounted to the firewall. If the fluid level is good then you may have a bad slave cylinder.|
|08-11-2010 10:19 PM|
|08-11-2010 10:17 PM|
|GoodsOfLiveng||OK thanks a lot banipal19, I will try that, if anyone else has any ideals please let me know!|
|08-11-2010 10:09 PM|
Welcome to the addiction!! And it is a Jeep not a car .
Your clutch problem sounds like you are low on clutch fluid. Check that and report here ..
|08-11-2010 09:03 PM|
Help Please! 5-Speed TJ Wrangler Problem: Clutch Engaging Low
This morning I got in my beautiful 2001 TJ Wrangler and started the car. I put the clutch all the way in and found I couldnít put the car in reverse, it made a sound as if the clutch wasnít in (almost like a gear grind sound) and I also found I couldnít put it into any gear.
I turned the car off, and then was able to change the gears, so I put it into reverse and backed out. It was very difficult to take out of reverse and impossible to put into first gear, so I turned the car off again and put it into first gear and drove about 200 feet, and I guess it warmed up or something, then I was able to shift gears, but only with great difficulty.
What I realized was that my clutch was engaging at a much lower point than usual, therefore I had to push it in much farther to change the gears, and all the way to the floor was still not quite far enough to get a smooth shift. With the car in first and the clutch all the way to the floor, I only had to lift my foot about half an inch for the car to move forward, and Iím used to it engaging about one-thirds up.
What I then realized thinking back was that a few days ago I noticed that I kept gear-grinding, which was really strange. Within about 20 minutes I gear grinded 4 times, when I hadnít done it in months, and I couldnít understand why that would happen, and now I realize itís because the clutch is engaging lower. Therefore, I am used to it engaging at a different point and Iím lifting it up too high to put the gear in and the gear grinded.
Iím really low on money, and my mom wonít pay for the $80 or so check-up to figure out what is wrong with it, which I know is the best way to go, but I simply donít have the money. If anyone could please help it would be much appreciated. Iím only 17 so I do not know too much about cars.
Thanks a lot