|08-15-2010 08:50 PM|
Note to self: make sure that I remove the old oil filter gasket from the engine before installing new filter.
Other than that this wrangler is the easiest oil change I have ever done. Am I correct in assuming that the reason such a small engine holds so much oil is because of the unusual sustained attitudes that a jeep can get in when off roading?
|08-15-2010 05:10 PM|
|08-15-2010 03:52 PM|
Synthetic at 3200 miles?
My question is: What is the consensus on changing to full synthetic at 3200 miles?
The owner's manual (pg 450) does not have any comments about when it is acceptable to change to synthetic, only that you always need to stick to the recommended change interval and specifications.
|08-15-2010 02:20 PM|
[QUOTE=ColdSRT;725130I have not looked in the jeep manual. Mainly because it is more of a "quick setup guide" but in my last jeep the salesman was sure to tell me that if I did my own work I must keep a log and receipts for consumables and parts. Then in the manual or the warranty booklet it said that warranty could not be denied based on the lack of maintenance records or receipts. As always, the better record keeping you do the less of a fight you may have on your hands when you make a warranty claim.[/QUOTE]
it's what I was told too.
Get a file folder, keep receipts and a written record.
|08-15-2010 02:08 PM|
|2010 Rubicon Black||Well, Thank you all for your responses... 3k then every 6k after that? Roger that!|
|08-15-2010 01:03 PM|
|08-15-2010 12:36 PM|
|08-15-2010 11:18 AM|
|silvrevo||Buy your filters from the dealership,and keep your receipts.|
|08-15-2010 10:54 AM|
|08-15-2010 10:46 AM|
So, is everyone in agreement, switch to synthetic after 6,ooo Km .. .. or is that 6,000 miles?
I am only a few kilometers from 6,000 .. and thinking about getting it done next week.
|08-15-2010 09:01 AM|
|cremaley||Did my first at 3,000 and will do the second at 6,000 and then every 6,000 thereafter. Using Mobile 1 suplied by the dealer for around $40.|
|08-15-2010 07:26 AM|
|08-15-2010 04:56 AM|
|2010 Rubicon Black||
Yes they are recommendations by a Moto GP Tec, but he also states that all 4 stroke engines should be broken in this way…
Either way all answers sound good to me, the initial break in does leave metal peaces in the engine and probable should be removed asap.
|08-15-2010 04:47 AM|
|08-15-2010 04:46 AM|
|2010 Rubicon Black||The above are recommendations by a moto GP Tec that states this is the way all 4 stroke engines should be broken in.|
|08-15-2010 04:42 AM|
|2010 Rubicon Black||I personally will change the oil myself soon and put a magnetic drain plug in with a good quality oil filter. (I picked up the K&N filters for 3 for $41 bucks) but that is what a oil change would cost anyways so if your going to do it then do it right! lol that’s what I am going to do, it can’t hurt.|
|08-15-2010 04:39 AM|
|2010 Rubicon Black||
This is what I read for break in secrets!!!
Q: If break- in happens so quickly, why do you recommend using petroleum break- in oil for 1500 miles ??
A: Because while about 80% of the ring sealing takes place in the first hour of running the engine,
the last 20% of the process takes a longer time. Street riding isn't a controlled environment, so most of the mileage may
not be in "ring loading mode". Synthetic oil is so slippery that it actually "arrests" the break in process before the rings can seal completely. I've had a few customers who switched to synthetic oil too soon, and the rings never sealed properly no matter how hard they rode. Taking a new engine apart to re - ring it is the last thing anyone wants to do, so I recommend a lot
of mileage before switching to synthetic. It's really a "better safe than sorry" situation.
Q: My bike comes with synthetic oil from the factory, what should I do ??
A: I recommend changing the factory installed synthetic oil back to petroleum for the break-in period.
Q: What about the main and rod bearings, don't they break - in ??
A: Actually, the operation of plain bearings doesn't involve metal to metal contact !! The shiny spots on used
bearings are caused from their contact with the crankshaft journals during start up after the engine has been sitting a while,
and the excess oil has drained off. This is the main reason for not revving up the engine when it's first started.
The subject of plain bearings is one of the most mysterious aspects of engines, and will be covered in a future issue
of Power News. In it, I'll reveal more information that fully explains the non-contact phenomenon.
Q: Why change the oil at 20 miles ?? Doesn't the oil pick up
screen catch the aluminum bits ???
A: It's true that the screen stops the big pieces, but many areas of the engine aren't within the oil filtration system. The oil that is splashed around will circulate metal debris to the lubricated bearing surfaces. For example, transmission gears and their ball bearings are unprotected by the filtration system, and even the cam chain makes a perfect "conveyer belt" to
bring metal debris up into the cylinder head !!
A close examination of a new engine will reveal lots of aluminum deposits on steel parts. This aluminum coats and tightens
up the clearances of the parts, which creates a loss of power. Most of the time I spend "blueprinting"
an engine is actually inspecting every part and "de-aluminizing" them !!
I prefer to remove the oil pan and clean the aluminum bits out of a new engine out that way, but a $20 oil change
is an easy and inexpensive way to flush the initial particles that come loose in the first miles.
|08-15-2010 04:17 AM|
|Steel02001||The manual shows every 6,000. I literally just picked mine up and they said they would see me in 6,000 miles. (or when my hard top comes in)|
|08-15-2010 04:00 AM|
Where'd you read that?
I did my first oil change at 3k and now will do them every 6k.
|08-15-2010 03:49 AM|
|2010 Rubicon Black||
Thank you all! And another question, I have heard that the Jeep JK 3.8 should have its first oil change around 500 miles. Then read it should be changed after the initial break in at 20 miles…. 20 miles? Well it’s to late for that I have 99 miles and now thinking about changing at 150-200 with K&N filter and regular 5-20w.
Does anyone have a recommendation to what weight to use? I have read that if you take your 3.8 in with clicking noise they use 5-30w, should I use the 5-30w for break in?
|08-15-2010 12:29 AM|
|Steel02001||As the others have said, you need to keep detailed records of everything to include receipts.|
|08-15-2010 12:03 AM|
|ColdSRT||I have not looked in the jeep manual. Mainly because it is more of a "quick setup guide" but in my last jeep the salesman was sure to tell me that if I did my own work I must keep a log and receipts for consumables and parts. Then in the manual or the warranty booklet it said that warranty could not be denied based on the lack of maintenance records or receipts. As always, the better record keeping you do the less of a fight you may have on your hands when you make a warranty claim.|
|08-14-2010 11:30 PM|
|daggo66||No. Keep a maintenance log.|
|08-14-2010 11:20 PM|
|2010 Rubicon Black||
Will I void my warranty?
I just picked up my 2010 Rubicon and want to do all maintenance myself. My question is will it void my warranty if I do my own oil changes and differential changes?
Thanks to all that reply.