|02-06-2014 12:15 AM|
|eyeball||MG Chemicals 847 Carbon Conductive Assembly Paste.|
|02-05-2014 10:34 PM|
|01-20-2014 11:39 PM|
|WhiskeyMike||Once you remove the powdercoat, is there anything you can put on the metal to inhibit rust that will last more than a couple weeks.|
|01-12-2014 12:21 PM|
|sparky||Mak, you're not confused. The best you can do is 1:1. Meter is probably fine, it's the reading of the meter.|
|01-11-2014 09:22 PM|
|12-02-2013 10:57 AM|
|Jerry Bransford||Going to a longer antenna won't help your issue in the least. I'll almost guarantee your problem is antenna mount related. Post a couple good sharp well lighted close-up photos of the top & bottom of the mount and we may be able to figure out the problem. At the least I can tell you where you need to grind the mount's powder coating away so the right parts will be grounded|
|11-30-2013 05:45 PM|
|11-30-2013 02:16 PM|
|11-30-2013 12:38 PM|
|11-28-2013 09:08 PM|
|302||It is the teraflex mount. I'm going to mess with the mount again, but I don't think it will help. Static is there regardless if jeep is running or not.|
|11-28-2013 03:36 PM|
First, the 18' coax cable length thing is nothing more than an old wive's tale. Not to mention that 18' is not even a multiple of the CB's 11 meter wavelength. The correct length of coax cable is the length it takes to connect the CB to the antenna with a little slack left over for future changes or needs.
And the length of antenna will have nothing to do with static, absolutely nothing. My CB is static free with my 2' Firestick FS-2 antenna.
What does the static sound like? Does the static start when you start your engine? If so, are you running aftermarket ignition wiring or no-resistor spark plugs?
How is the CB getting its power? Only by powering the CB directly from the battery can you be assured the CB is getting clean noise-free power. Many of the circuits in a Jeep you can get 12 volts from are too electrically noisy for a CB.
One more problem that can introduce noise into a CB is via the antenna mount when it isn't sufficiently grounded. An antenna mount's grounding requirements are more demanding than something like a light bulb would require. The mount needs a good bare metal to bare metal connection to what it is bolted to. And depending on what kind of antenna mount is between the antenna itself and the body mount, the bottom half of the antenna mount must also have a bare metal connection to the mount.
A picture of the type of antenna mount you have would be helpful.
|11-27-2013 12:48 PM|
the firestik is tuned to length, but there are some caveats - they even suggest the 4' over the 3' when possible.
Do you have any kinks in the coax? The remaining cable, ideally, is "s" gathered and kept from touching sides - don't just gather it up and zip-tie it, certainly don't trim it! You should have an 18' coax cable, too...
You can contact Firestik - the engineers there are VERY helpful to get your setup tuned and offer tricks and tips. Good people - they made me a Firestik customer for life.
|11-27-2013 09:38 AM|
Do cobra 75's generally have more static?
I've had a cobra 75 in my jeep for a while now and I have to turn the SQ way up to not even hear static. Fast forward, I instill a Uniden 520 in my wife's jeep and I can have the SQ almost barely turned up with ZERO static. Not to mention the Uniden sounds more clear than the Cobra.
The only install differences between the two was my wife's is mounted above the rear view mirror. Therefore, I had to run the coax along the top sport bar where in my jeep I ran the coax underneath the carpet. Both runs of coax are straight runs with no loops, etc. The other difference is I got a 4' firestick for my wife's jeep and I got a 3' fire stick.
Do you guys think that could be my issue, or is the cobra 75 a lower quality unit compared to the uniden? I'm about to grab a 4' antenna for my jeep, see if that works and if it doesn't just junking the cobra and getting a Uniden. Thoughts?