Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > JK Jeep Wrangler Forum > JK General Discussion Forum > Front and rear diff

Join Wrangler Forum Today


Thread: Front and rear diff Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-10-2010 06:02 PM
poosimagnet Thanks for the help guys , I took it back in and they added a little more lube and tightened the screw now my baby is as good as new and ready 2 go off road again
09-09-2010 01:28 PM
JIMBOX Thats your drain plug and it has pipe threads, so it should be tight, all pipe threads differ but I'd make sure it was at least 25 ftlbs, I don't know if the manual specifys or not, but thats what mine are set at and NO lEAK

The diff. cover should be tightened in a star pattern,,,just like the wheel studs, or diagonal as Dag says, torque anywhere between 25/35 lbft--but don't go any more than than--they break !!

Good luck

JIMBO
09-09-2010 12:57 PM
gdub BTW - Nice screen name... LOL
09-09-2010 12:47 PM
Raw1986 Who changed it? I'd certainly not go there again...u could always be a jerk and drive it till it locks up act a fool and get something for free. Or just look up the specs and tighten it like an honest person should.
09-09-2010 12:39 PM
jake_blue Definitely not hard to change your own diff fluid otherwise even I wouldn't be able to do it! I installed lube lockers during the last change, much easier than messing with sealant. I'd say there's no way that drain plug should be loose enough to loosen by hand... don't tighten it too much or you might strip it but fingertight cannot be right.
09-09-2010 12:11 PM
poosimagnet Ok it's actually leaking from here . Although I noticed i can tighten and loosen by hand , should it be this loose ??
09-09-2010 11:48 AM
poosimagnet
Quote:
Originally Posted by TerrorJ2001
Where is it leaking from? A pic would help. Normally when the fluid is changed, it spits out oil if it is overfilled.
Looked like from the bottom of the seal but then again I checked it late at night , I'll double check right now and post a pic
09-09-2010 10:41 AM
Ibuildembig I'm a copper ultra seal guy
09-09-2010 10:39 AM
Proud Rebel If its the diff covers I used lube locker gaskets they worked for mine, and are reuseable.
09-09-2010 10:04 AM
adrenaline little bit tougher to do if it is leaking from the pinion seal. It can be done yourself with the proper tools. I recommend a dealer service manual!
09-09-2010 08:27 AM
TerrorJ2001 Where is it leaking from? A pic would help. Normally when the fluid is changed, it spits out oil if it is overfilled.
09-09-2010 08:27 AM
Raw1986 If u get the torque sequence and spec the fluid change is a cake walk especially since it was recently done
09-09-2010 08:07 AM
daggo66 First check the torque of the bolts. I could be wrong, but I beleive they should all be torqued to 25 foot pounds. You should work in a clockwise diagonal pattern when tightening the bolts.
09-09-2010 01:06 AM
poosimagnet
Front and rear diff

Well I just got my front and rear diff resealed about 2weeks ago but I decided 2 do some late night offroading last night and what would u know the front diff is leaking again . So my question is how hard would it be for me 2 reseal it myself ?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 10:46 AM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC