Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ Tech Forum > Lower Control arm Skids

Join Wrangler Forum Today


Thread: Lower Control arm Skids Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-16-2010 09:42 AM
mrcarcrazy Rich, any pics of the engine skid?

PM sent.
09-16-2010 08:22 AM
rbraden1970 Thanks for all the info.
09-16-2010 06:53 AM
rrich By the way - the lower control arm skid's insert ties the 2 ears together, significantly adding strength.

The actual skid plate itself is removable with bolts and is replaceable. (In case you actually do bend it.) And once removed total access to the ends of the control arms is easy.

The skid plate is a solid bent 1/4" steel plate, not pieced together, with gussets. The bend actually lets it wrap around the bracket for full protection.

It fits both stock and all control arms that I've ever encountered.

For use in the rear the end of the plate may need to be notched slightly to allow the arm to swing it's full travel. That depends on the suspension arms and the amount of lift.

If the LCA bracket's ears are already bent or distorted, they need to be bent back straight before installation. When bending them back you'll be surprised at how weak they are. They are only made of about 1/16" (Shame on Jeep for making them so flimsy.)

Yes, it cuts down on ground clearance - it reduces ground clearance by just over 1/4".

When I hear a loud "BANG" underneath, I'd rather laugh than cringe!
09-16-2010 03:03 AM
rrich As I said, I'm out of that business now.
But I still have a few of the lower control arm braces and skid plates. 4 or 5 sets I think. They probably have a little rust, and need a little paint, but they are new (leftovers.)

Free to anyone who wants them. I'll probably need $10.00 for shipping.

PM me if you want a set.

I'm cleaning out one of my shops. I may have 1 or 2 engine skid plates too.
09-16-2010 02:56 AM
rrich While you are at it - strengthen another weak area - the axle end of the right upper control arm.
Box it in, add gussets on both sides.

Yes, they snap right off!
09-16-2010 02:52 AM
rrich Strengthening the stock control arm prevents this:

It's very easy to bend those things.
09-16-2010 02:44 AM
rrich They can take a severe beating - and protects the mounting ears from bending or breaking.
09-16-2010 02:41 AM
rrich I used to sell these on E-bay - $120 a pair. Fits front or rear.

I'm out of that business now.
09-16-2010 02:37 AM
rrich another insert
09-16-2010 02:35 AM
rrich The insert
09-16-2010 02:34 AM
rrich Prevents this - or worse!
09-16-2010 02:27 AM
rrich It's easy to make them near bullet proof.
Remove them one at a time.

Cut 2 lengths of 1.25 x .120 tube to fit inside the stock arms. Weld them in place inside the channel.

Now cut a 2" ? wide piece of flat 3/16 to box it in, weld it in place.

Careful when you get near the ends that you don't damage the rubber bushings, keep dousing the ends in water to keep them cool.

For the uppers use one piece of 1" tube and do the same.

They'll be stronger than any aftermarket arms made from tubing.

I've done probably 20 or so TJ's like that, so far nobody has bent one.

For the axle mounts - make a piece of 3/16 the width between the ears. Drill and tap two holes 1/2. Weld that piece between the ears in front, tying the 2 ears together.
Make a 1/4" skid plate to bolt to the holes.
09-16-2010 12:25 AM
rbraden1970
Quote:
Originally Posted by IndyJeepMan View Post
Yeah, there is nothing you can do about rock rashing the actual arms, but to get tubular adjustables. But the skids protect where they are most vulnerable, at the joint.
I know I need the skids to. I actually did better at not taging the bracket so hard but sliding over stuff worked on the arms pretty good.
09-16-2010 12:24 AM
rbraden1970
Quote:
Originally Posted by IndyJeepMan View Post
I believe Rokmens ACA would work for stock or 2" application or higher.
Just looked them up that would work. Thanks
09-16-2010 12:20 AM
IndyJeepMan Yeah, there is nothing you can do about rock rashing the actual arms, but to get tubular adjustables. But the skids protect where they are most vulnerable, at the joint.
09-16-2010 12:19 AM
IndyJeepMan I believe Rokmens ACA would work for stock or 2" application or higher.
09-16-2010 12:17 AM
rbraden1970
Quote:
Originally Posted by IndyJeepMan View Post
You weld the skids on to the control arm braket that is located on the axle tube.

I have the JKS ones, with stock control arms they wont work, unless you trim the bottom down.

But even with tube CA itd be nice to have the skids there so the Johnny's dont take a beating.
I know which ones you are talking about to protect the mounting bracket, there on my list. The control arms themselves are getting scraped along the bottoms sliding over rocks. really shows how flimsy they are.
09-16-2010 12:14 AM
rbraden1970 That is kind of what I was thinking. Most of the after market adjustables that I have run across list that they are for 4" or higher lifts. Any suggestions on ones that would be stok length up to at least 2" lift?
09-16-2010 12:14 AM
IndyJeepMan You weld the skids on to the control arm braket that is located on the axle tube.

I have the JKS ones, with stock control arms they wont work, unless you trim the bottom down.

But even with tube CA itd be nice to have the skids there so the Johnny's dont take a beating.
09-16-2010 12:11 AM
jwm1986 It'd be a lot more effective to just get some heavy duty tube control arms... The stock ones don't seem to put up with much on rocks from what i've seen, and the metal is so thin I don't think welding anything on to them would really help anything.
09-15-2010 11:20 PM
rbraden1970
Lower Control arm Skids

Any thoughts on boxing in factory lower control arms. Went wheeling last weekend and they got pretty scratched up sliding across rocks. I know there are skids for the front mounts on the axle but thought about welding a plate to the bottom of the control arms so to strengthen them. Anyone tried it or does it make them to rigid? Thought I would see what others might think.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 08:23 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC