|09-17-2010 02:35 PM|
Actually... It's bass ackwards if that was the mentality behind it... black absorbs heat and white reflects it, so black inside and white outside would keep it cooler and the current configuration would keep the maximum amount of heat in the cab.
More likely to have been an economical or aesthetic decision, but That's just my best guess. They could very well have thought it would be cooler (no pun intended).
No matter the reason, that liner job is flippin awesome
|09-17-2010 01:59 PM|
I am finding out that everything always adds up quickly with Jeep accessories.
Thanks for clearing up why they used white on the inside. I never thought of that, but it really doesn't get that hot in central Ohio as it would in TX, AZ or NM. So I will just have the soft top down.
|09-17-2010 12:54 PM|
Nice job. Boy, the materials cost adds up in a hurry doesn't it!
I for one don't mind the white top...doesn't bother me. They used white so it wouldn't radiate as much heat into the cabin from the black exterior. I'll be anxious to hear your experience after painting it black.
|09-17-2010 12:18 PM|
The fabric I used was from Jo-Ann's, not being a smart a--, but it's called Headliner fabric. It exactly lilke what is on your headliner of your cars. It comes in different colors. It was like $15 a yard and I used 5 yards, becasue I messed up on a piece. I also bought their headliner spray glue there, it was $20 a can and I used two of them. And that stuff is sticky, once you place the headliner on you can forget about trying to pull it back off, not going to happen. You need to be careful when smoothing it out on the board, you might get a wrinkle in it. I have one, made me mad! but it's over the back seat so I don't have to look at it all day.
Home Depot is where I got the Aluminum U and L chanel about $8 a piece I used 5 U and 1 L chanel. The board is like a pressed cardboard you can get it in 4X8 sheets. i used two of them. Put the soft top down and strapped them to the roll bar to get them home. That was a fun trip, wife was worried they were going to fly off and it looked wierd. I just used rattle can paint it was a Rustolym (sp) type.
I used B-Quiet sound deadener, around $85 for a 12"X 50' roll. I barely used any. Used the rest of it on the wife's SUV. You might be able to look around and find smaller rolls.
The biggest thing I can say is, make templates! much easier to work with then trying to trim the actual panels. The side window template were the hardest becasue of all the angels.
If you have any other questions let me know. I can post some other shots of the process if needed.
|09-17-2010 11:33 AM|
That looks great. I've been thinking of adding insulation to our hard top -- it seems that DC winters are getting colder and the summers are getting hotter.
|09-17-2010 10:37 AM|
Where are you located and would you do it again for money?
|09-17-2010 10:19 AM|
|GREEN-MACHINE||damm i gotta get my ass in gear, looks freaking awesome. what materials gig you use for the liner.|
|09-17-2010 09:14 AM|
|clear lake jeepn||Looks good. If I had a hardtop I would want in black on the inside too.|
|09-17-2010 06:16 AM|
For the top, I just scuffed it down with a scotch brite pad and then wipe it down with some alcohol.
The interior of the jeep is black and gray, so the black top goes better with it then the white, in my opinion.
I drove it around a little bit after I put the top back on yesterday and to me it seemed pretty quite. But I am going from 2 months with the soft top and majority of that time not having the soft top up to having the hard top on. So I might need a little bit of time to adjust. I can say I used the deadener in my wife's Mariner, I gutted her suv and put it everywhere and it really made a difference.
|09-16-2010 07:42 PM|
|Ageless Stranger||The insulation turned out nice. I hope the black works out OK for you. All in all, nice job.|
|09-16-2010 07:39 PM|
|Steel02001||What sort of prep did you do to the top before painting?|
|09-16-2010 07:23 PM|
|Steel blue sahara||i like the black better than the white. i dont understand why they have it white to begin with i think it looks weird. let us know how the sound deadeners work.|
|09-16-2010 07:10 PM|
Hard Top Makeover
I have been working on it for a while between, well about 4 weeks in between all my sons stuff and work. But I finally finished fixing up the inside of my hard top.
I painted everything black, multiple coats. I also put sound deadener on all the areas where I made the head liner. Then covered the board with black headliner and fastened with aluminum u-channel all around the sides. I just put it back on the jeep and I think it looks great. A lot better then the glaring white before. The pics kind of show the headliner a different color, that's just the pic. Everything is black on the inside now.