Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > TJ Jeep Wrangler Forum > TJ General Discussion Forum > hows this setup sound to you guys.

Join Wrangler Forum Today


Thread: hows this setup sound to you guys. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-26-2010 04:28 PM
Jerry Bransford
Quote:
Originally Posted by wpark013 View Post
if you are gonna do the 1" bl and 2" spacers then you should get 32s or even 33s
3" of clearance (1" BL and 2" spacers) isn't quite enough for 33" tires for offroad use. It's barely adequate for street use and 33" tires. 4" is strongly recommended for 33" tires for a TJ that actually does offroad trails tougher than a fire access road or dirt road.
09-26-2010 03:00 PM
wpark013 if you are gonna do the 1" bl and 2" spacers then you should get 32s or even 33s
09-26-2010 02:36 PM
Jerry Bransford Tom knows the length driveshaft needed for most lift/transmission/axle combinations. Talk with him and see if he won't already know the length needed for your combination.

Most SYE kits are very similar quality. The one I would personally not install is a Super Short. First, you don't need that for any commonly installed lift heights. Second, and my biggest objection, is that you lose the speedometer gear and its easy speedometer calibration ability with a super-short SYE which requires you buy an extra cost ($80-200) electronic speedometer calibrator that has to be wired in.
09-26-2010 02:31 PM
Nicholson Is there a way to figure out the length of driveshaft required before the lift is installed? From what I was reading on Tom Wood's website the measuring has to be done after the lift is installed.

Also what are the differences in quality or advantage/disadvantages between the Advance Adapters, Super Short, and Super Duty conversions? It looks to me like the XB configuration is the best for longevity, anyone have any experience in the result of installing that option?

Tom Wood's Custom Drive Shafts - SYE
09-26-2010 01:26 PM
AtcoTrailsINC thanks guys ill look on to the tom wood and what he offers
09-26-2010 12:51 PM
Jerry Bransford X2 on getting your SYE kit and CV driveshaft from Tom Wood (not Woods). Tom is a gentleman and not only provides great quality parts, his pre and post-sales support is unsurpassed. I met Tom years ago and he is truly a refreshing individual.

http://www.4xshaft.com/index.html
09-26-2010 12:47 PM
yjkid95 I know tom woods cv style drive shaft is a popular choice i think its one of those things where you'd install the SYE then measure how long of one you need and place the order. I could be wrong though.
09-26-2010 12:44 PM
AtcoTrailsINC thanks jerry thats exactly what i was hoping dumb question but where to i find a CV drive shaft to go along with the SYE? or do some SYE kits come with it?

EDIT: nvm i answered my own question with a little search on quadratec. HOLY F***. they are not cheap lol.
09-26-2010 12:29 PM
Jerry Bransford Yes you can install the SYE without dropping the entire t-case, just remove the rear case half and it's an easy job. I'd rather do it that way than remove the entire transfer case as it's faster and easier. Back the Jeep up onto a pair of car ramps so you'll have more working room underneath.

And make sure you have a set of snap ring pliers that open widely enough. Not many do, most do not. Note that I did not say "high quality" snap ring pliers, that's not necessarily the same as having them being able to open widely enough. I couldn't find any that opened widely enough in my local tool supply stores. I ended up buying mine from a tool truck parked at one of my former Jeep dealership clients. I think it was a Snap-on tool truck.
09-26-2010 12:22 PM
AtcoTrailsINC [QUOTE=yjkid95;789176]He needs the SYE and CV driveshaft if hes doing a tummy tuck. To me it sounds like you have a good setup there. If I had a tj or lj id go for low center of gravity but tons of clearance and big tires check out rokemens tummy tuck skid. They would have some stuff you'd be interested in.[/QUOT


You hit the nail on the head Plan is to keep a LCG while gaining as much clearance as possible. That and if i decide to go taller in the future im set. not a big fan of dropping the transfer case lower then it already is soooo counter productive
09-26-2010 12:14 PM
yjkid95 He needs the SYE and CV driveshaft if hes doing a tummy tuck. To me it sounds like you have a good setup there. If I had a tj or lj id go for low center of gravity but tons of clearance and big tires check out rokemens tummy tuck skid. They would have some stuff you'd be interested in.
09-26-2010 12:07 PM
530ktm Why do you want to do the SYE if you are only doing a 2 inch lift and running 31 or 32 inch tires. You can still do the small lift and the 1 inch body lift and save yourself a bunch of money by not doing that part. Do the body lift and add the 1 inch motor mount lift and your skid plat can remain right where it is.
09-26-2010 12:03 PM
AtcoTrailsINC
hows this setup sound to you guys.

So im planning out the next big steps for the jeep later down the road. Shes all stock now minus some lighting and steering box skid. My plans are to first install an SYE. Can i install the SYE without dropping the whole transfer case? Next im going to do a 1inch body lift so i can get a tummy tuck. finally, a 2inch lift ( cant decide on coil or just spacers yet) and a nice set of 31's or maybe 32's.

hows that setup sound to you guys? anyone running something similar? Ide like to hear what you guys think

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 05:18 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC