Jeep Wrangler Forum - Reply to Topic
Jeep Wrangler Forum

Go Back   Jeep Wrangler Forum > CJ Jeep Forum > CJ General Discussion Forum > Rebuild Project-- Diesel?

Join Wrangler Forum Today


Thread: Rebuild Project-- Diesel? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the Jeep Wrangler Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-25-2010 11:59 AM
Ibuildembig It all depends, I am into my 6bt, nv4500, and dana 80 for 425.00 after I sold the rest of the truck
10-25-2010 11:57 AM
Ggg Not trying to knock a diesel swap but they are pricey to do. My guess is in the $6-8000 range when it is all said and done.
09-27-2010 02:41 PM
phantomofrussia sounds like a fun project ahead of you and those teens. Good luck.
09-27-2010 02:26 PM
SBakerUMC The project looks like it might be lifting off of the ground as a few more people come in board. I would like to keep you all updated, but this might be a slow project. Keep the ideas and tips coming. I will need all of the help that I can get.
09-25-2010 05:44 PM
RSC17 Good luck with this, subscribed.
09-25-2010 05:26 PM
BEHR2010 The diesel swap can be done there are plenty of other routes besides a cummins also like the lighter Mercedes diesels that are in their older cars I've seen a couple of these or chevy 6.5. It would be a bit more exspensive to convert to a diesel but from what I hear the guys with diesels in jeeps are getting around 30MPG if not more.
09-24-2010 11:28 PM
Ibuildembig That's the average salvage price yes...but if you do some digging you can find better deals. When I start a project I sit down with 12 pack and a pad of paper. I think about what the rigs intended purpose is, how I want it to look, and when I want it done. The last thing I think about is budget because I feel if you work under the budget tent all the time you never reach the goal you are going for.
09-24-2010 11:06 PM
SBakerUMC ANy more suggestions?
09-23-2010 04:32 PM
SBakerUMC thats not that bad. I assume that is the salvage price?
09-23-2010 04:21 PM
Ibuildembig Its all gonna depend on what you want really...carb or efi? automatic or manual? If your gonna use a ford in a CJ your gonna have to get a Dana 300 case and flip it upsidedown so your driveshaft will work on the CJ front axle. IF you use a wrangler front axle or a ford one, you can use a ford case. I'd say in the ballpark your looking at a good 2200.00 for all the parts minus axles to do one with injection.
09-23-2010 04:15 PM
SBakerUMC I am open to Ford. What would I be looking at then?
09-23-2010 04:13 PM
Ibuildembig Dunno, I am a Ford man so I can't price gm stuff for ya.
09-23-2010 04:09 PM
SBakerUMC The Diesel thing sounds cool. Especially if we could run bio or something. HPA used a 1.9L VW engine out of a Jetta TDI (or something) and all of the running parts. Gave it a flash boost and it got 165bhp and something like 285ft/lbs. and it weighed alot less than stock. I even think there is a kit for using the stock t-case and such. Just engine/tranny and other diesel specific parts. If I went gas I want to go Chevy Small Block V6/8 with an automatic TH400 tranny if the Jeep turns out to be a CJ7 for a CJ5 I will go with same engine with a TH350. Are these gas options easily available from salvage yards?

What are some price estimates on engine swaps?

Frame wise, I would say if I stay with springs, thanks for the tip on the YJ frame. If going to coils, then does anyone have experience converting using the TDK custom frames?
09-23-2010 03:56 PM
Ibuildembig Well I for one will never say something can't be done, since I have spent my life doing those things lol

No way I would buy an aftermarket frame considering a 7 tub and and a YJ tub are nearly identical. Plus a YJ will outdrive a CJ any day of the week. As far as suspension goes, that's gonna be up to your motor choice and preference. For instance a 4BT cummins weighs around 780#'s fully dressed, so that's gonna take heavier springs and a heavier duty front axle.

I'd say think about what you want for a motor and post it...everyone will be glad to give input. Just an FYI, diesels aren't worth a crap in the mud unless you boost the hell out of um....no rpm = no tire speed = stuck
09-23-2010 03:50 PM
SBakerUMC
Rebuild Project-- Diesel?

Hey guys,
I am thinking about starting a new project. I have an opportunity to get a junker jeep CJ5 or CJ7 to rebuild. I can do anything I want with it (money being the only limit). I don't know if it runs. i don't know if the frame is good. I don't know a whole lot about it. All I do know is that is really cheap, and I need a project to work on with some older high schoolers in my community that tend to get in to trouble when they don't have a goal. They like cars/tucks and jeeps. Here are some questions that I have just to throw them out there, but first I want this jeep to be a rock climbing, mud slinging, show(ish) jeep.

1. Engine Swap- Should I go GM small block V6 or try and do the impossible-- DIESEL SWAP?!

2. Frame-- Can you correct and old frame? If not, Should I get a TDK factory replacement or a TDK CJ/TJ hybrid frame and run a coil suspension?

3. Suspension-- If I stay with springs, is SOA conversion a good idea? or should I go with an aftermarket type lift?

Its out there now and look for more questions in the future as me an this rag tag bunch of teenagers try and do this.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -5. The time now is 09:21 PM.



Jeep®, Wrangler, Liberty, Wagoneer, Cherokee, and Grand Cherokee are copyrighted and trademarked to Chrysler Motors LLC.
Wranglerforum.com is not in any way associated with the Chrysler Motors LLC