|10-03-2010 12:55 AM|
|harwa004||Gotta do mine this week. Some idiot keyed my rear passenger one...DEEP.|
|10-03-2010 12:50 AM|
|flyboy86q||I did my flares and bumpers this week. I just masked it off as well. Seemed to go faster. Mine were nearly white from the previous owner.|
|10-02-2010 08:18 PM|
Now thats just plain cheating
nice man wish I'd thought of doing that to mine.
|10-02-2010 07:45 PM|
Does this count?
|10-02-2010 12:27 PM|
|10-02-2010 02:51 AM|
|oldskool71||took the passenger side flares off this afternoon...gonna give them a shot tomorrow...wish me luck...|
|10-01-2010 04:40 PM|
|10-01-2010 04:13 PM|
|wolfen||Been there done that, I used Krylon Fusion for plastic things so far so good|
|10-01-2010 01:49 PM|
|10-01-2010 07:19 AM|
|ParaCAD||yea thanks for posting...good job!|
|10-01-2010 05:56 AM|
I like the color on your jeep.
|10-01-2010 05:53 AM|
|blkrubi88||Flares look great!|
|10-01-2010 04:25 AM|
|oldskool71||I about to do this myself....I was planning on removing mine though...do you have to use sandpaper on them first though?..by the way thanks for taking the time to take pics and post this...very helpful.|
|10-01-2010 12:33 AM|
Painted Fender Flares (Yawn) - Pics Though!
After searching through the forum for how to paint fender flares I decided to give it a go today with some Krylon Fusion in Satin Black. Rather than completely remove them, I opted to leave them on and try to make up with it in prep work. This was mainly because I didn't have an optimal work area. My only regret there is that I wasn’t able to hit the undersides of them but for now it’s fine.
I had tried almost every product (including Mother’s Back to Black) in efforts to keep the flares looking OK but none of them worked very well in my opinion. I’m convinced the fading was accelerated by my girlfriend’s liberal use of Amor All, which I think is the crack cocaine of detail products. Looks great for a day but then you need to apply more.
Photo #1: Masking and prep work. I didn’t need to loosen the flares as there was already enough play between them and the body to slide the masking paper in. This photo also shows what the flare looked like after I sanded it with 150 grain paper (I would suggest sanding as it’s very little extra work.) This was done after wiping down the freshly washed fenders with Windex to get any leftover grime.
Photo #2: Just shows the before state of the front right flare, lots of fading on the body extension portion. Sorry about the lighting in the first two photos but the was some morning fog.
Photo #3: Here’s how the right rear flare looked after about two coats compared with the front right (still unpainted.) I kind of leapfrogged around the Jeep, prepping one flare, going back and spraying another coat on the last one, so on and so forth to save time.
Photo #3: The right front flare. I just pulled the running light lens and disconnected the lighting harness, then backed the opening with masking paper.
Photo #4: Finished product – I’m happy! No more cheap, greasy shine, just a nice textured satin black now. Why couldn’t Jeep have thought of this at the factory?
Photo #5: The only screw up was leaving the masking behind the right front flare for too long, hence a little flaked off when I removed the backing. I think I can touch it up though. A guy I used to paint for taught me a long time ago to always pull your masking while to paint’s still wet to get super clean lines (wish I had remember that this afternoon.) In any event, I hope this paint job lasts because I'm not going to do it again.
So that’s it. A couple of notes: 1.) I found that the Krylon Fusion has a bit of texture when it dries so that and my OCD prompted me to hit each fender like seven time. It also meant I used almost 3 cans of Krylon. One portion of the left rear flare had some drips in it so after that coat dried, I lightly sanded it down and resprayed it. Overall time was 3-4 hours. Could have been a little faster if I had been more confident with my spray skills.
Thanks to all the member s of the forum who have posted their information here for newbies like me to find. Hope the photos help the next person.